Votes - 4, Average rating: 4.3
(
)
)
|
manual abstract
1. Slide the Volume slider down and at the same time, use the stylus to press the RESET button at the back of your device. Volume SliderRESET button 2. After a brief period of time, two choices will appear on-screen. Press the CENTER OK button to perform the hard reset. Note If you do not want to perform a hard reset, press the CAMERA button to exit. 3. Press the POWER button. 14.6 Checking System Information If you want to find out about technical details about your device such as the type or speed of the processor, memory size, etc., you can check under Settings for device information. To find the operating system version number • Tap Start > Settings > System tab > About. The version of the operating system on your device is shown near the top of the About screen. To get detailed device information • Tap Start > Settings > System tab > About. The Version tab displays important device information, including the type of processor and the amount of memory that is installed. 14.7 Battery Saving Tips How long your battery power lasts depends on battery type and how you use your device. Try the following to help preserve battery life: To find the operating system version number • When the device is not in use, press POWER to switch off the display. • Tap the battery icon ( ) on the Today screen. On the Advanced tab of the Power settings screen, you can specify when your device automatically turns off the display to conserve battery power. For optimum conservation, specify 3 minutes or less. • Use the AC adapter to plug your device into external power whenever possible, especially when using a microSD card or when using a modem or other peripherals. • Adjust the backlight settings. For more information, see “To set the backlight to dim after a time delay” in Chapter 4. • Turn Bluetooth off when you are not using it. • Make the device visible to other devices only when you are trying to establish a Bluetooth partnership. For more information, see “Using Bluetooth” in Chapter 9. • Enable your device to receive incoming beams setting only while you are trying to receive beamed files. To find this setting, tap Start > Settings > Connections > Beam. • Lower the volume. • Close battery-intensive programs, such as the Camera, when you are done using them. Make sure the programs are ended and are not continuously running in the background. For more information about ending running programs, see “To close a program” in this chapter. Appendix A.1 Regulatory Notices A.2 PC Requirement to Run ActiveSync 4.x A.3 Specifications 232 Appendix A.1 Regulatory Notices Regulatory Agency Identifications For regulatory identification purposes, your product is assigned a model number of ATHE100. FCC ID: NM8ATHE100. To ensure continued reliable and safe operation of your device, use only the accessories listed below with your ATHE100. The Battery Pack has been assigned a model number of ATHE160. This product is intended for use with a certified Class 2 Limited Power Source, rated 5 Volts DC, maximum 1 Amp power supply unit. European Union Notice Products with CE marking comply with the R&TTE Directive (99/5/EC), the EMC Directive (89/336/EEC), and the Low Voltage Directive (73/23/EEC) issued by the Commission of the European Community. Compliance with these directives implies conformity to the following European Norms (in parentheses are the equivalent international standards). • EN 60950-1 (IEC 60950-1) Safety of InformationTechnology Equipment. • ETSI EN 301 511 Global system for mobile communications (GSM); Harmonized EN for mobile stations in the GSM 900 and GSM 1800 bands, covering essential requirements of article 3.2 of the R&TTE directive (1995/5/ EC). • ETSI EN 301 489-1 Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 1: Common technical requirements. • ETSI EN 301 489-7 Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 7: Specific conditions for mobile and portable radio and ancillary equipment of digital cellular radio telecommunications systems (GSM and DCS). • ETSI EN 301 489-17 Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment Appendix 233 and services; Part 17: Specific conditions for 2.4 GHz wideband transmission systems and 5 GHz high performance RLAN equipment. • EN 301 489-24 Electromagnetic compatibility and radio spectrum matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 24: Specific conditions for IMT-2000 CDMA direct spread (UTRA) for mobile and portable (UE) radio and ancillary equipment. • EN 301 908 Electromagnetic compatibility and Radio spectrum Matters (ERM); Base Stations (BS) and User Equipment (UE) for IMT-2000 third generation cellular networks. • ETSI EN 300 328 Electromagnetic com...