Votes - 3, Average rating: 4.3 ( )

Manafacture: Panasonic File size: 7.46 mb File name: Language of manual:

Photos and specs  Panasonic  ES-LA93

213“Dry/ CourseCourse selection indicationsTime required (guide) [In the low temperature] . Charge Charge (0 to 60 min) Clean (10 min) . Clean/Dry/ Charge Dry (80 min [170 min]) Charge (0 to 60 min) Dry (180 min) . Dry/Charge Charge (0 to 60 min) English 7 ES-LA93_CIS.indb 7 2010/01/06 16:44:50 English Follow the steps outlined below if the status lamp blinks or glows during the “Clean/Dry/Charge” course. Blinks Glows Correctly set the detergent cartridge and then restart a course. Remove the shaver from the selfcleaning recharger and then check that the [CLEAN] lamp has gone out. (Be careful as the blade may be hot or wet.) Check that the water tank is correctly attached, the water tank cap is securely closed and the selfcleaning recharger is placed horizontally. If the status lamp goes out Continue a course. When an abnormality has been corrected When no abnormality was found Press and hold [SELECT] for approximately 2 seconds to turn off the status lamp and then restart a course. It is time to replace the detergent cartridge and cleaning liquid inside the water tank. Drain the old cleaning liquid inside the water tank and then refill it with water. Replace the old detergent cartridge and then restart the course. When the status lamp goes out When the status lamp glows again Continue a course. Contact an authorized service center. . Cleaning the shaver without the self-cleaning recharger We recommend that you clean your shaver with the self-cleaning recharger or the turbo mode for “sonic” vibration cleaning when the faucet symbol appears on the LCD panel. 1. Disconnect the power cord from the shaver. 2. Apply some hand soap and some water to the outer foil. 3. Slide the switch lock button downwards to unlock the OFF/ ON switch. 4. Press the OFF/ON switch for more than 2 seconds to activate the turbo mode for “sonic” vibration cleaning. appears on the LCD panel. After about 20 seconds, it will be automatically turned off, or you can turn it off by pressing the OFF/ON switch. 5. Remove the outer foil section and press the OFF/ON switch for more than 2 seconds to activate the turbo mode for “sonic” vibration cleaning and clean it with running water. 6. Wipe off any drops of water with a dry cloth. • • 7 ES-LA93_CIS.indb 8 2010/01/06 16:44:50 English 7. Dry the outer foil section and the shaver completely. 8. Attach the outer foil section to the shaver. 9. Lubricate the shaver. Caution for turbo mode Shaving in turbo mode may damage your skin. Turn the shaver off and then on again to cancel turbo mode. Do not place your fingers on the OFF/ON switch while using the shaver. This may cause the shaver to turn off or enter turbo mode. • • Lubrication To maintain shaving comfort for a long time, it is recommended that the oil provided with the shaver is used. 1. Switch off the shaver. 2. Apply one drop of oil to each of the outer foils. 3. Raise the trimmer and apply a drop of oil. 4. Switch the shaver on, and run it for approximately five seconds. 5. Switch off the shaver, and wipe off any excess oil from the outer foils with a soft cloth. It is not necessary to oil the blades after using the self-cleaning recharger (lubricant is included in the cleaning detergent). • Replacing the system outer foil and the inner blades appears on the LCD panel once a year. (This will differ depending on usage.) We recommend checking the system outer foil and the inner blades when it appears. Press the OFF/ON switch for more than 30 seconds to delete . system outer foil once every year inner blade once every two years Replacing the system outer foil 1. Press the foil frame release buttons and lift the outer foil section upwards as illustrated. 2. Press the system outer foil release buttons and pull down the system outer foil as illustrated. 3. Align the foil frame mark and the system outer foil mark and securely attach together. The system outer foil cannot be reversely attached. Always insert the system outer foil to the foil frame when attaching to the shaver. 4. After turning the mark to the front, securely attach the outer foil section to the shaver until it clicks. • 2 3 • • . ES-LA93_CIS.indb 9 2010/01/06 16:44:51 10 English Replacing the inner blades 1. Press the foil frame release buttons and lift the outer foil section upwards as illustrated. 2. Remove the inner blades one at a time as illustrated. Do not touch the edges (metal parts) of the inner blades to prevent injury to your hand. 3. Insert the inner blades one at a time until they click as illustrated. • 2 3 Cleaning with the brush (A) (B) 1. Clean the inner blades using the short brush by moving it in direction (A). Clean the system outer foil, the shaver body and the trimmer using the long brush. Do not move the short brush in direction (B) as it will damage the inner blades and affect their sharpness. Do not use the short brush to clean the outer foils. • • . Cleaning the self-cleaning recharger Beard trimmings may become attached to the cleaning tray of the self...

Download now

Please, enter two numbers from picture: