Votes - 2, Average rating: 5 ( )

Manafacture: Bryant File size: 1.14 mb File name: om538-691m-01.pdf Language of manual:

To install or replace batteries: 1. Slide the back cover off the control to open the battery compartment. 2. Insert batteries. Follow the polarity markings inside the battery compartment. 3. Replace battery compartment cover. NOTE: 1. When replacing batteries, do not use old batteries or a different type battery. This may cause the remote control to malfunction. 2. If the remote is not going to be used for several weeks, remove the batteries. Otherwise battery leakage may damage the remote control. 3. The average battery life under normal use is about 6 months. 4. Replace the batteries when there is no audible beep from the indoor unit or if the Transmission Indicator fails to light. Set the Clock Before you start operating the air conditioner, set the clock of the remote control as outlined below. The clock panel on the remote controller will display the time regardless of whether the air conditioner is in use or not. Initial Setting of the Clock: After batteries are inserted in the remote control, the clock panel will display ”12:00” and begin to flash. 1. TEMP Button S Press these buttons to set the time: YForward BBackward S Each time you press the button, the time moves forward or backward by one minute depending on which button you press. S If you push the temperature button continuously, the time adjusts in increments of 10 minutes. 2. CLOCK Button When the right time is achieved, press the CLOCK button or release Y or the B button and wait for 3 seconds, the clock time stops flashing and the clock starts operating. 3. Readjusting the Clock Press the CLOCK button on the remote control for about 3 seconds, the time of the clock display will start to flash. To set the new time, follow 1 and 2 of ”Initial Setting of the Clock”. NOTE: Note: The time of the CLOCK must be set before the AUTO--TIMER function will operate. Clock accuracy is within 15 seconds per day. UNIT OPERATION HAZARD Failure to follow this caution may result in equipment damage or improper operation. Static electricity or other factors (voltage fluctuations) can cause the remote control clock to reset. If your remote control is reset (the time of ”12:00” flashing), set the clock before starting the unit. ! CAUTION 6 Remote Control Operation -- Quick Start NOTE: When transmitting a command from the remote control to the unit, be sure to point the control toward the right side of the unit. the unit will confirm receipt of a command by sounding an audible beep. 1. Turn the unit on by pushing the ON/OFF button. 2. If there is a preference for temperature settings to be displayed in _F rather than _C (default), push the recessed F/C button once using a paper clip or similar object. 3. Select the desired mode by pushing the mode button. AUTO COOL DRY HEAT FAN NOTE: Cool only units have no heat mode. 4. Select the temperature set point by pointing the control toward the unit and pressing the increase/decrease temperature set point buttons until the desired temperature appears on screen. 5. Select the desired fan speed by pressing the FAN SPEED button to select desired fan speed. NOTE: If unit is operating in Dry mode, AUTO fan speed will be displayed. 6. Set the airflow direction. When the unit is turned on, the louvers default to the cooling or heating position. The user can adjust louver position by pushing the air direction button or have continuous louver movement by pushing the swing button. Emergency Operation If the remote control is lost, damaged, or the batteries are exhausted, the MANUAL button can be used to run the unit. Open the front cover panel and press the MANUAL button once briefly when the system is off. To stop emergency operation, push the MANUAL button twice or operate the remote control. If the MANUAL button is only pushed once, the system will enter TEST mode and run for 30 minutes. Manual button A07364 The set conditions of emergency operation are as follows: S Preset set point: 76_F (24_C) S Fan speed: AUTO S Discharge air direction: Pre--set position based on operation in “Cool”or “Heat” mode. REMOTE CONTROL FUNCTIONS Pressing the On/Off Button SET TEMP. C L O C K SPEED AUTO AUTO ON/OFF INDICATOR A08034 When the air conditioner is not in operation, the remote control will display the last set point, mode and time. S Press the On/Off button to start the unit. -- The unit will start in the last operating mode and set point. The ON/OFF indicator will appear. S Press button On/Off to stop the unit. -- All indicator lights on the unit will go out, and the remote control will display the set point, mode and time. NOTE: If the On/Off button is pressed too soon after a stop, the compressor will not start for 3 minutes due to the inherent protection against frequent compressor cycling. The unit will only emit an audible beep when the signals are received correctly. Selecting an Operating Mode Use the Operating Mode button to select one of the available modes. SET TEMP. C L O C K SPEED AUTO OPERATING MODE AUTO COOL DR Y HE AT ...

Download now

Please, enter two numbers from picture: