Votes - 0, Average rating: 0
(
)
)
|
manual abstract
When a certain level is reached an indicator light, Fig. 3, comes on indicating that the condensed water tank is full and needs to be emptied. When this happens, the appliance stops cooling the air in the room until the water is drained, as explained in "Transportation requirements", Fig. 7. • It is recommended that you turn the appliance off while draining the water. Warning! Remember that when the appliance is turned off and turned back on, it is necessary to wait for approximately 3 minutes before the compressor starts up again. This period of time is required in order to ensure correct appliance operation. Ways of releasing air outdoors Fitting the air expulsion tube and accessories onto the appliance. Fit the air expulsion tube assembly into the housing on the top of the appliance at the back, Fig. 11. 40 Fig. 10 Fig. 11 Fig. 12 Fig. 13 Fig. 14 Fig. 9 Housing for the air expulsion assembly Instructions for Use • The accessory has two holes on the side to fit it to the window / balcony with. The user can secure it to the frame or wall with two screws (not included with the accessory) to prevent it from moving or falling out of place, Fig. 16. • The sliding window/balcony installation accessory can also be used (See “Description of accessories”), Fig. 15 : a, b, c, d. This accessory can be used for both horizontal and vertical windows / balconies. 41 Permanent installation Permanent installation is performed using the wall grommet window See "Description of accessories". • To expel hot air through the wall, it is n e c e s s a ry to make a hole in the wall and fit the wall grommet, Fig. 17. 24 - 38 cm. • Remove the diffusion sleeve and connect the air expulsion tube to the accessory. • If permanent installation is to be performed through the window, then it is only necessary to use the transparent end piece on the accessor y. A 10.5-cm diameter hole needs to be cut in the glass, Fig. 18. Fig. 16 Fig. 17 Fig. 18 Notes: Do not extend the hot air expulsion tube more than necessary (maximum length; 140 cm). Do not form sharp bends when positioning the tube, otherwise the a Fig. 15 a b c d Instructions for Use 42 Do not form sharp bends when positioning the tube, otherwise the correct expulsion of hot air may be impeded. This may cause a reduction in the cooling power and performance of the appliance. In order to achieve maximum cooling efficiency and minimum noise levels, the expulsion tube should be fitted above the total height of the appliance, Fig. 19. Dehumidification In position the appliance reduces the humidity in the atmosphere. • Set the thermostat to its minimum temperature setting, Fig. 20. • Place a bowl at the drainage pipe outlet and remove the plug to collect the condensed water, Fig. 21. • Remove the diffusion duct and set the air expulsion tube to the position shown in figure 22. • The expulsion tube may also be totally dismantled if desired. • Lift the air director on the top of the appliance. This air director is not installed on the appliance on 3XM411E models. See figures 25 and 26 in "Heating". • Select the dehumidification function on the control knob, Fig. 23. Warning! The amount of dehumidified water may reach a maximum of 36 litres in 24 hours, depending on ambient conditions. See "Technical Information". Do not forget to replace the plug onto the water drainage pipe when you change function, otherwise the 90° 0° Fig. 19 Fig. 20 Fig. 21 Fig. 22 Fig. 23 Instructions for Use 43 appliance will shed water when operated. Remember that ambient temperature must be 18.C or higher in order for the appliance to work. Air purification The air entering the room (ventilation) is circulated through a purifying filter when the appliance is set to this function. The appliance is fitted with a basic filter and a purifying filter for: - Pollen, bacteria and dust. • Put the air expulsion tube in the same position as for dehumidification. • Lift the air director on the top of the appliance. This air director is not installed on the appliance on 3XM411E models. See figures 25 or 26 in “Heating”. • Select the purifying speed: maximum or silent , Fig. 24. • When the appliance or the model is fitted with optional filters, we recommend that these be left on regardles...
Other models in this manual:Air Conditioner & Split Systems - 3XM411E/01 (2.61 mb)
Air Conditioner & Split Systems - 3XM420E/01 (2.61 mb)
Air Conditioner & Split Systems - 3XM420E/02 (2.61 mb)
Air Conditioner & Split Systems - 3XM420E/03 (2.61 mb)