Votes - 2, Average rating: 4.5 ( )

Manafacture: Kenmore File size: 1.72 mb File name: Language of manual:

SLEEVE ASSEMBLY (Including Aluminum Rear grille) 10. REAR GRILLE (Aluminum Rear grille) -13 USING THE AIR CONDITIONER _To reduce the risk of fire, electdc shock, or injury to persons, read the important SAFETY instructions section before operating this appliance. To begin operating the air conditioner after installation, follow these steps: 1. Plug in the air conditioner. (To prevent electrical hazards, do not use an extension cord or an adapter plug.) 2. Set the TEMP control to the coolest setting. 3. Set the MODE control at the highest COOL level. 4. Adjust the louvers for comfortable air flow. 5. Once the room has cooled, adjust the TEMP and MODE control to the setting you find most comfortable. NOTE : If the air conditioner is turned off, wait 3 / minutes before restarting. This allows pressure inside the compressor to equalize. Failure to wait 3 minutes before restarting may cause inefficient operation. If you move the TEMP control to a warmer, then immediately back to a cooler setting, the unit will shut off. Wait 3 minutes before restarting. Refer to the AIR CONDITIONER FEATURES section for other settings. VENT CONTROL The Vent Control allows the air conditioner to either recirculate inside air (CLOSE) or exhaust air to the outside (OPEN). (FIG. 28) • The CLOSE position is used when maximum cooling is desired. It may also be used for air recirculatioo without cooling when the air conditioner is set in the FAN position. • The OPEN position removes stale air from the room and exhausts it to the outside. Fresh air is drawn into the room through your home's normal air passages. • The OPEN or CLOSE position can be used with any fan selection. PULL OPEN / PUSH CLOSE FIG< 28 CONTROL PANEL -FAN SPEED Every time you push this button, it advances the setting as follows: {High , Low _Med * High} (-TIMER -SHUT-OFF TIME • You will usually use shut-off time while you sleep. • If unit is running, use Timer to set number of hours until shut-off. • For your sleeping comfort, once Time is set, the Temperature setting will raise 2°F after 30 min., and once again after another 30 min. • Push Timer button to advance setting from 1Hour * 2Hours * ... > 12Hours maximum. -START TIME • If unit is off, use Timer to set number of hours before unit starts. • Push Timer button to advance setting from 1Hour >2Hours >... * 12Hours maximum. MODE -Push this button to shift mode of operation from COOL -COOL: • Fan runs continually for normal cooling operation -ENERGY SAVER: Applied to 580.75085 580.75116 RECEIVER • Use this button to automatically controlthe temperature of the room. The temperature can be set within a range of 60°F to 86°F by increments of I°F. • The setting appears in the display. • To turn the air conditioner ON, push this button. To turn the air conditioner OFF, push the button again. • This button takes priority over any other button. • When you first turn it on, the unit is in cool mode, High fan speed, Temperature setting at 72°F. >ENERGY SAVER >FAN. • The fan stops when the compressor stops cooling. Approximately every 3 minutes the fan will turn on and the unit will check the room air temperature to determine if cooling is needed. -FAN: • Fan-only operation. _ed after an electrical power failure, the unit will begin to run at its last setting. ] -14 REMOTE CONTROL NOTE: The Remote Control wiEInot operate properly if strong light shines on the sensor window of the Air Conditioner or ifthere are obstacles between the Remote Control and the Air Conditioner. Every time you push button, you will hear a beep from the Air Conditioner. POWER • To turn the air conditionerON, push this button, To turn the air conditionerOFF, pushthe buttonagain, • This button takes priorityover any other button. • When you first turn it on, the unit is in cool mode> High fan speed, Temperature setting at 72°F. • Auto Restart In the event at a power failure, the unit will run at the previoussetting once power returns. • Temp • TEMPERATURE SETTING • Use this button to automatically control the temperature of the room. The temperature can be set within a range of 60°F to 86°F by Fan Speed increments of I°F. • The setting appears in the display. / Timer Mode FAN SPEED • Everytimeyoupushthisbutton itadvancesthe settingas follows: (High * Low * Med * High) TIMER -SHUT-OFF TIME • You will usually use shut-off time while you sleep. • If unit is running, use Timer to set number of hours until shut-off. • For your sleeping comfort, once Time is set, the Temperature setting will raise 2°F after 30 min, and once again after another 30 min. • Push Timer button to advance setting from 1Hour * 2Hours + ... * 12Hours maximum. -START TIME • If unit is off, use Timer to set of hours before unit starts. • Push Timer button to advance setting from 1Hour * 2Hoors * ... 12Hours maximum. MODE -Push this button to shift mode of operation from COOL • ENERGY SAVER * FAN. -COOL: • Fan runs continually for normal cooling operation -ENERGY SAVER: • The fan stops w...

Download now

Please, enter two numbers from picture: