Votes - 2, Average rating: 3 ( )

Manafacture: Heat Controller File size: 904.14 kb File name: (OM)ASU18CL.pdf Language of manual:

If the difference between the thermostat setting and actual room temperature is more than +4 °F > Cooling or dry operation If the difference between the thermostat setting and actual room temperature is +4 °F or less > Monitor operation . When the thermostat setting of air conditioner has been adjusted to near the room temperature or the room temperature becomes lower than the thermostat setting, it will begin monitor operation. In the monitor operation mode, the fan will operate at low speed. If the room temperature subsequently changes, the air conditioner will once again select the appropriate operation (Cooling) to adjust the temperature to the value set in the thermostat. (The monitor operation range is in the temperature of +4 °F or less relative to the thermostat setting.) . If the mode automatically selected by the unit is not what you wish, select one of the mode operation (COOL, DRY, FAN). About Mode Operation Cooling: Use to cool your room. Dry: Use for gently cooling while dehumidifying your room. You cannot heat the room during Dry mode. . During Dry mode, the unit will operate at low speed; in order to adjust room humidity, the indoor unit’s fan may stop from time to time. Also, the fan may operate at very low speed when adjusting room humidity. The fan speed cannot be changed manually when Dry mode has been selected. Fan: Use to circulate the air throughout your room. During Cooling/Dry mode: Set the thermostat to a temperature setting that is lower than the current room temperature. The Cooling and Dry modes will not operate if the thermostat is set higher than the actual room temperature (in Cooling mode, the fan alone will operate). During Fan mode: You can not use the unit to cool your room. En-6 05M150_9315255020-01_En 6 2005.12.15, 10:56 TIMER OPERATION Before using the timer function, be sure that the Remote Control Unit is set to the correct current time ( P. 4). sTo Use the ON timer or OFF timer 1 Press the START/STOP button (Fig. 6 Q) (if the unit is already operating, proceed to step 2). The indoor unit’s OPERATION Indicator Lamp (red) (Fig. 3 5) will light. 2 Press the TIMER MODE button (Fig. 6 N) to select the OFF timer or ON timer operation. Each time the button is pressed the timer function changes in the follow- ing order: CANCEL OFF ON PROGRAM(OFF > ON, OFF < ON) The indoor unit’s TIMER Indicator Lamp (green) (Fig. 3 6) will light. 3 Use the TIMER SET buttons (Fig. 6 O) to adjust the desired OFF time or ON time. Set the time while the time display is flashing (the flashing will continue for about five seconds). button: Press to advance the time. button: Press to reverse the time. About five seconds later, the entire display will reappear. To Use the Program timer 1 Press the START/STOP button (Fig. 6 Q). (if the unit is already operating, proceed to step 2). The indoor unit’s OPERATION Indicator Lamp (red) (Fig. 3 5) will light. 2 Set the desired times for OFF timer and ON timer. See the section “To Use the ON timer or OFF timer” to set the desired mode and times. About three seconds later, the entire display will reappear. The indoor unit’s TIMER Indicator Lamp (green) (Fig. 3 6) will light. 3 Press the TIMER MODE button (Fig. 6 N) to select the PROGRAM timer operation (OFF ON or OFF ON will display). The display will alternately show “OFF timer” and “ON timer”, then change to show the time setting for the operation to occur first. The program timer will begin operation. (If the ON timer has been se- lected to operate first, the unit will stop operating at this point.) About five seconds later, the entire display will reappear. About the Program timer To Cancel the Timer Use the TIMER button to select “CANCEL”. The air conditioner will return to normal operation. To Change the Timer Settings Perform steps 2 and 3. To Stop Air Conditioner Operation while the Timer is Operating Press the START/STOP button. To Change Operating Conditions If you wish to change operating conditions (Mode, Fan Speed, Thermostat Setting, SUPER QUIET mode), after making the timer setting wait until the entire display reappears, then press the appropriate buttons to change the operating condition desired. sstTo Cancel the Timer Use the TIMER MODE button to select “CANCEL”. The air conditioner will return to normal operation. To Change the Timer Settings 1. Follow the instructions given in the section “To Use the ON Timer or OFF Timer” to se- lect the timer setting you wish to change. 2. Press the TIMER MODE button to select either OFF ON or OFF ON. To Stop Air Conditioner Operation while the Timer is Operating Press the START/STOP button. To Change Operating Conditions If you wish to change operating conditions (Mode, Fan Speed, Thermostat Setting, SUPER QUIET mode), after making the timer setting wait until the entire display reap- pears, then press the appropriate buttons to change the operating condition desired. . The program timer allows you to integrate OFF timer and ON timer operations i...

Download now

Please, enter two numbers from picture: