Votes - 2, Average rating: 4
(
)
)
|
manual abstract
Press "A" or "▼ "buttons to select number of hours before the unit automatically starts running in air conditionning mode. NOTE: The time is adjustable between 1-24 hours. TEMPERATURE Adjust: • Used for adjusting the thermostat. • The default display is room temperature. • In cooling mode, when "am or button is pressed, the set temperature is displayed and may be adjusted. After 15 seconds the display will revert back to room temperature. Temperature is only adjustable in cool ode. " buttons at the mod 7 NOTE: By pressing both " same time for more than 3 seconds, the display will toggle between Celsius and Fahrenheit. STATUS DISPLAY Warning Light Condensed water may accumulate in the unit. If the internal tank becomes full, the Warning signal in the LCD Display will light up and the unit will not operate until the unit has been drained. fiffi Timer & Temp. Display • Room Temp. H • Temp. Set ° • Timer Set *• MODE INDICATOR LIGHTS Cooling Mode When cool mode is selected, the indicator light will shine GREEN. During the cooling mode, the air is cooled and hot air is exhausted outside through the exhaust tube. Adjust fan speed to suit your desired comfort level. Note: The air exchange h ose must vent outside the room when using cool mode. * Dehumidify Mode When dehumidil fy mode is selected, the indicator OR light will shine Orange. Air is dehumidified as it passes through the unit, without being in full cooling mode. The fan will operate on med. speed. If room temperature is >25°C (77°F), fan speed can be adjusted; otherwise fan speed is fixed to “low”. Note: The warm air exchange hose must vent inside the room when using Dehumidify Mode, not outside as it does when cooling. If the unit is vented outside, some cooling will occur. **[Fan Mode When fan mode is selected, the indicator will shine YELLOW. Air is circulated throughout the room with no cooling. Note: The unit does not need to be vented in Fan mode. • During Fan/Dehumidifier mode, the temperature cannot be set. FAN SPEED INDICATOR LIGHTS • *lHigh Fan •* Medium Fan •* Low Fan NOTE: AFTER SWITCHING THE AIR CONDITIONER OFF, YOU MUST WAIT 3 MINUTES BEFORE SWITCHING IT BACK ON AGAIN. <6> OPERATING INSTRUCTIONS (cont’d) AIR CONDITIONING IMPORTANT: The exhaust hose must be properly vented (outdoors) during air conditioning mode. 1) Press the POWER SWITCH key (Fig. A) to switch on the unit, and the previous set temperature will be shown in the temperature display area of the control panel. 2) Press the MODE key (Fig. B) until the COOL indicator light illuminates on the control panel (Fig.C). Each depression of the MODE key will advance to a different mode setting (Cool-Dehumidifier-Fan-Heat-Auto) 3) Press the appropriate increase "am or decrease buttons (Fig. D) to select a suitable operating temperature setting. Temperature settings are adjustable between 16°C (61°F) to 32°C (89°F). 4) Press the FAN key (Fig. E) to select the desired fan speed setting (Auto-High-Med.-Low). Your selection will appear on the control panel (each depression of the fan key will advance to a different setting). • Cooling stops automatically when the set temperature is achieved. Cooling resumes when the room temp. rises above the “set” temperature level. Fig. A Fig. B DEHUMIDIFIER Note: During dehumidifier mode, the exhaust hose does not have to be vented outdoors. 1) Press the ON/OFF key pad to switch the unit on (Fig. A) 2) Press the MODE key (Fig. B) until the DRY indicator illuminates on the control panel (Fig.G). Each press of the MODE key will advance to a different mode setting (Cool-Dehumidifier-Fan-Heat-Auto). ^— 3) If room temperature is >25°C (77°F), fan speed can be adjusted. Press the [fIcjTh FAN key (Fig. E) to select the desired FAN SPEED setting. Your selection will appear on the control. Each depression of the fan key will advance to a different fan speed as shown in Fig. F. Otherwise fan speed is fixed to “low”. NOTE: The warm air exchange hoses must vent inside the room when using Dehumidify Mode, not outside as in Cooling Mode. ¿¿¿1 FAN NOTE: During Fan Mode, the exhaust hose does not have to be vented outdoors. 1) Press the POWER SWITCH key to turn the unit on (Fig. H). 2) Press the MODE key (Fig. I) until the FAN indicator illuminates on the control panel (Fig. J). Each press of the MODE key will advance to a different mode setting (Cool-Dehumidifier-Fan-Heat-Auto). 3) Press the FAN Key (Fig. K) to select the desired FAN SPEED setting. Your selection will appear on the control panel. Each press of the fan key will advance to a different fan speed (High- Med- Low) as shown in Fig. L. Fig. L 4. High Medium Low Fig. I Fig. J d Yellow <7> REMOTE CONTROL FEATURES Control Buttons: 1) Power Switch 2) Mode 3) Fan Speed 4) On / Off Timer 5) Time / Temperature Set • Used for adjusting the timer and temperature. 3 — • The default display on control panel is room temperature. • When " ® " or " e...