Votes - 2, Average rating: 3.5
(
)
)
|
manual abstract
The exhaust hose(s) should alwaysbe used in cooling mode. The air intake hose can be used to increase the cooling efficiency of the unit. If the air intake hose is not used, simply cover one of the grated adapters on the plastic window kit with a vent cap. © I O Q 1. Plastic window kit..............................2 pieces 2. Grated adapter..................................2 pieces 3. Screws..............................................8 pieces 4. Duct connector.................................2 pieces 5. Exhaust hose....................................2 pieces 6. Window kit connector........................2 pieces 7. Vent cap............................................2 pieces 1. Loosen the screws on the plastic window kit(1) and adjust the sliding kit to the width or height of your window. Then tighten the screws to secure your adjustments to the window kit. (See below images for setup examples) 2. Place one of the grated adapters(2) into one of the hole on flush side of the plastic window kit(1). Line up the 4 holes in the grated adaptor(2) with the pilot holes in the plastic window kit and fasten them together with a screw driver. Repeat for the other grated adaptor(2). 3. Install the plastic window kit(1) into your window. If necessary, use duct tape to better secure the window kit. 4. On the air conditioner, connect the duct connectors(4) (the connectors with the smaller slots) into the unit by aligning the tabs inside the unit with the slots and snapping them together. (See Fig. 1). Note: Once inserted, duct connectors cannot be removed. 5. Attach the window kit connectors(6) (the connectors with the larger slots) onto the exhaust hoses(5) by stretching the hoses completely out and turning the window kit connectors(6) clockwise, screwing them into the exhaust hoses(5). 6. Screw on the exhaust hoses(5) to the duct connectors(4) by turning them clockwise. 7. Move the air conditioner towards the window. Align the slots on the window kit connectors(6) to the tabs on the grated adapters(2) and snap them together. (See Fig. 2) 8. To remove the window kit connectors(6) from the grated adaptors(2), push in the tabs on the grated adaptors(2) and pull the window kit connectors(6) away from the grated adaptors(2) 9. To remove both the window kit connectors(6) and duct connectors from the exhaust hoses, twist the connections counterclockwise. To remove the grated adaptors(2) unscrew the 8 screws(3). 10. The vent caps(7) may be installed on the grated adapters(2) (by aligning the slots with tabs and snapping them together) when the air conditioner is not in use. (See Fig. 3) Duct Connector Exhaust Hose Window Kit Connector Fig.2 lAJi Fig.3 Maintenance / Appliance maintenance QCut off the power supply Turn off the appliance first before disconnecting from the power supply. o Wipe with a soft dry cloth. Use lukewarm water (below 104°F) to clean the appliance. €> Never use volatile substance such as gasoline or polishing powder to clean the appliance. Never spray water onto the main unit. Air filter maintenance It is necessary to clean or replace the air filters periodically. Clean as follows: OStop the appliance and remove the activated carbon filter and the pre-filter. The activated carbon filter attaches to the standard pre-filter. The activated carbon filter removes smoke, odors and other harmful particles, while the pre-filter removes dust. Clean and reinstall the pre-filter Dirt can be cleaned off the pre-filter by washing it with a solution of soap in lukewarm water. After cleaning the pre-filter, allow it to air dry in shaded and cool place, then reinstall. Clean the pre-filter every two weeks if the air conditioner operates in a dusty environment. ©Replace the activated carbon filter The activated carbon filter can notbe cleaned and needs to be disposed of when cleaning the pre-filter. EdgeStar sells replacement activated carbon filters. Contact customer service via email at service@edgestar.com or by telephone at 1-866-319-5473 to purchase additional activated carbon filters. Maintenance and Storage 1. If you are not going to use this unit for a long time, be sure to drain the water from the reservoir by removing the drain cap and the rubber plug. 2. Before storing the unit, run it in fan mode for a few hours to dry any moisture on the coils to prevent mold. 3. Turn the unit off, clean the air filter and reinstall it. 4. Remove the exhaust hose and connectors and keep them in a safe place. Optimizing Performance / For Maximum Performance and Efficiency: 1. Do not cover the air outlet (exhaust) while in use. 2. Do not place the unit in front of curtains or drapes- to ensure they do not obstruct the air intake. 3. Minimize the length of the exhaust hose. 4. Make sure the exhaust hose is as straight as possible. 5. Keep curtains, blinds or drapes closed during the sunniest part of the day. 6. Use the timer to operate the unit before it is needed. For ex...