Votes - 3, Average rating: 4
(
)
)
|
manual abstract
The set temperature will be displayed for 15 seconds, then revert back to room temperature. The temperature is only adjustable in cooling mode. The time is adjustable between 1-12 hours. Note: By pressing both of the Timer/Temp button the same time, the display will toggle between Celsius and Fahrenheit. Note: The displayed range of the ambient temperature in both celsius and farenheit is from 0° to 99°. Any temperature above 99° will be displayed as “HI” on the indicator, and any temperature below 0° will be displayed as “LO.” • Dehumidifying Mode The dehumidifying mode removes water from the air without cooling the room. If the room temperature is below 77°F, the fan speed will be locked on “low,” above 77°F, the fan speed is adjustable. Note: The exhaust hose is not required in dehumidifying mode. Note: The internal water tray will fill with water in this mode. After turning the air conditioner off, wait 3 minutes before turning it back on again. Installation Accessories 1. Plastic window kit.............................2 pieces 2. Grated adapter.................................1 piece 3. Screws..............................................4 pieces 4. Duct connector.................................1 piece 5. Exhaust hose....................................1 piece 6. Window kit connector........................1 piece 7. Vent cap............................................1 piece 1. Loosen the screws on the plastic window kit(1) and adjust the sliding kit to the width or height of your window. Then tighten the screws to secure your adjustments to the window kit. (See below images for setup examples) 2. Place the grated adapter(2) into the large hole on the flush side of the plastic window kit(1). Line up the 4 holes in the grated adaptor(2) with the pilot holes in the plastic window kit and fasten them togethe with a screw driver. 3. Install the plastic window kit(1) into your window. If necessary, use duct tape to better secure the window 4. On the air conditioner, connect the duct connector(4) (the connector with the smaller slots) into the unit by aligning the tabs inside the unit with the slots and snapping them together. (See Fig. 1). Note: Once inserted, duct connectors cannot be removed. 5. Attach the window kit connector(6) (the connector with the larger slots) onto the exhaust hose(5) by stretching the hose completely out and turning the window kit connector(6) clockwise, screwing it into the exhaust hose(5). 6. Screw on the exhaust hose(5) to the duct connector(4) by turning it clockwise. 7. Move the air conditioner towards the window. Align the slots on the window kit connector(6) to the tabs on the grated adapter(2) and snap them together. (See Fig. 2) 8. To remove the window kit connector(6) from the grated adaptor(2), push in the tabs on the grated adaptor(2) and pull the window kit connector(6) away from the grated adaptor(2) 9. To remove the window kit connector(6) and duct connector from the exhaust hose, twist the connections counterclockwise. To remove the grated adaptor(2) unscrew the 4 screws(3). 10. The vent cap(7) may be installed on the grated adapter(2) (by aligning the slots with tabs and snapping them together) when the air conditioner is not in use. (See Fig. 3) kit. Fig.2 *=■ ul 1 Duct Connector Exhaust Hose Window Kit Connector Optimizing Performance / For Maximum Performance and Efficiency: 1. Do not cover the air outlet (exhaust) while in use. 2. Do not place the unit in front of curtains or drapes- to ensure they do not obstruct the air intake. 3. Minimize the length of the exhaust hose. 4. Make sure the exhaust hose is as straight as possible. 5. Keep curtains, blinds or drapes closed during the sunniest part of the day. 6. Use the timer to operate the unit before it is needed. For example, set the timer to turn on the unit in cooling mode for 3 or more hours to cool the room before you arrive. You may want to operate the unit all day if you live in a warmer climate. 7. Minimize the heat sources (direct sunlight, computers, servers, people, etc.) in the room. 8. Close all windows and doors. 9. Use the unit in a contained room. For example, a room with four walls and a roof, instead of a partitioned studio, or warehouse. 10. Make sure the unit is on a level surface. 11. Minimize the amount of humidity in the room. For example, adding a dehumidifier. 12. To prolong the compressor's life, please wait at least 3 minutes before turning the unit back on after shutting it off. 13. Inspect and keep the pre-filters clean by cleaning regularly. 14. Inspect and replace the activated carbon filters regularly. 15. Perform routine maintenance. Maintenance / Appliance maintenance o Turn off the appliance first before disconnecting from the power supply. 0 Wipe with a soft and dry cloth Use lukewarm water (below 104°F) to clean the appliance. 0 Never use volalile substances such as gasoline or polishing powder to clean the applia...