Votes - 3, Average rating: 3.7
(
)
)
|
manual abstract
Connecting the duct connector to the unit Connecting the duct connector to the grated adapter 7. Align the slots on the duct connector to the tabs and snap into the back of the unit. 8. Align the slots on the duct connector to the tabs on the grated adapter and snap in place. . .. 9 Your portable air conditioner is designed to exhaust condensate water that is collected from the air. This water, in either gaseous or droplet form, will be expelled out the exhaust port of the unit. Please take this into account when deciding how to vent it. 1. The exhaust hose supplied with the portable air conditioner can be extended up to 48 inches; however for maximum efficiency, use the shortest length possible. 2. Try to prevent any kinks or bends in the exhaust hose. Kinks or bends may trap exhaust air which can radiate heat into the room or potentially cause the portable air conditioner to overheat and shut itself off. 3. The exhaust hose supplied with the portable air conditioner has been specifically designed for this air conditioner. Do not lengthen the hose by adding additional hoses or attachments or replace it with any other hose. Do not lengthen the exhaust hose by adding additional hoses or attachments. Warning: Longer hoses are not recommended. Draining the Unit When the portable air conditioner is in cooling mode, or dehumidify mode, it will remove moisture from the air. The condensed water from the air will be collected in an internal reservoir and will be evaporated and exhausted out of the exhaust hose. However, in very humid conditions, the internal reservoir may fill completely. This causes the air conditioner to turn off to avoid overflowing the internal reservoir. The WATER indicator will light up on the Control Panel. Direct drainage 1. Remove the rubber drain plug from the drain port. 2. Connect a drain hose to the drain port. The portable air conditioner will now drain through the drain hose. Please note that this unit has no drain pump; all water will drain with gravity only, i.e., only “downhill.” Notes about the Exhaust hose EdgeStar Portable Air Conditioner 10 Remote Control Overview 1) Remove the cover on the back of the remote control. 2) Insert the batteries with the (+) and (-) ends pointing in the correct direction. 3) Slide the cover back on. Installing the batteries Button Function Power Powers the unit on or off. Fan Speed Sets the fan speed. The Automatic, High, Medium or Low indicator will appear depending on the mode you set. Mode Sets the mode. The Automatic, Cool, Dehumidify and Fan indicator will appear depending on the mode you set. (Down) Decreases the Temperature, Timer, or Clock settings. (Clock) Used to set the remote control clock Timer Used to enable the timer. C/F Switches the temperature between Celsius/Fahrenheit (Up) Increases the Temperature Timer, or Clock settings. Power Button Fan Speed Button Mode Button Down Button Clock Button Timer Button Celsius/Fahrenheit Button Up Button LCD Display C/F CAUTION: Use only AAA batteries. Remove the batteries if the remote control will not be used for one month or longer. Do not attempt to recharge batteries not designed to be recharged. All batteries should be replaced at the same time. Do not mix old and new batteries. Do not dispose of batteries in a fire as they may explode. 11 Remote Control LCD Indicators Indicators Transmitter Appears when the Power or Timer button is signaling the unit. Fan Speed Shows the set fan speed between Automatic, High, Medium and Low. Mode Shows the set mode between Automatic, Cooling, Dehumidify, Fan Only. Temperature Setting Shows the set temperature. Fahrenheit and Celsius Shows if the set temperature is in Fahrenheit or Celsius. Clock Shows the Clock’s time. The remote control has a 24-Hour clock. Timed Hours Shows the number of timed hours when the Timer is enabled. Timer Shows if the On Timer or Off Timer is enabled. Mode Indicator Function Automatic The unit will cool, dehumidify or heat (some models) depending on the ambient temperature. The mode and fan speed changes automatically. The front panel lights will change to reflect the running mode. Cooling The unit will cool. The front panel lights will be blue. Dehumidify The unit will remove moisture from the air. The front panel lights will be yellow. Fan Only The unit will run as a fan and circulate air. The front panel lights will be green. Fahrenheit and Celsius Indicator Timer Indicator Timed Hours Clock Indicator Mode Indicators Speed Indicators Transmitter Indicator Temperature Setting Indicator EdgeStar Portable Air Conditioner 12 Operating the Remote Control Use the Power button to turn the portable air conditioner on and off. By default when you first use the power button, the unit will begin to operate in cooling mode and the front panel will be illuminated in blue. The unit will remember the last used mode/settings if you shut down and restart. Auto-Restart: If power to the unit is interrupted, the air conditioner will restart i...