Votes - 4, Average rating: 4.3 ( )

Manafacture: Dell File size: 1.1 mb File name: bx960s1-ba-en.pdf Language of manual:

– Flashes to indicate an active network connection. – Does not light up if there is no network connection. ID card You can pull out the ID card (see figure 6 on page 41 above) as far as it will go and push it back in again. The ID card contains various system information, such as product name, serial number and order number; in the Japanese market only the product name and the serial number. 44 Operating Manual BX960 S1 Switching the Server Blade on and off 5.2 Switching the Server Blade on and off V CAUTION! If you switch the server blade on and flickering stripes appear on the connected monitor, switch the server blade off again immediately (see chapter "Troubleshooting and tips" on page 53). The On/Off button does not disconnect the device from the mains. To fully disconnect the device from the mains, you must remove the server blade from the system unit or switch off the system unit and unplug the power plug(s). Using the control panel to switch the Server Blade on and off The system unit is switched on and the power-on indicator (item 8 in figure 6 on page 41) is flashing green. The server blade can be switched on and off as follows: – To switch the server blade on, press the On/Off button on the server blade (item 8 in figure 6 on page 41). To switch the server blade off, hold down the On/Off button on the server blade (item 8 in figure 6 on page 41) for 4 seconds. Defined switch-on/off time The server blade is switched on and off at the times defined in the ServerView Operation Manager. Other On/Off options – After power failure Once a server blade has been switched on, it will switch itself on again automatically after a power failure (irrespective of the setting in the BIOS Setup). I You can also switch the server blade on and off via the system unit control panel or via the Web interface of the ServerView Management Blade. Detailed information is provided in the manual "PRIMERGY BX900 Blade Server Systems ServerView Management Blade S1 User Interface Description". BX960 S1 Operating Manual Configuring the Server Blade 5.3 Configuring the Server Blade This section contains information about configuring the server blade and installing the operating system. The operating system can be installed in various ways: – Local installation with or without the ServerView Installation Manager You can find information on local installation in the following sections. – Remote installation using console redirection via the user interface of the ServerView Management Blade You can find information on console redirection in the manual "PRIMERGY BX900 Blade Server Systems ServerView Management Blade S1 User Interface Description". Apart from this, the operating system installation is carried out in the same way as a local installation. – Importing the clone images from an image repository to the desired server blades. For more information about this procedure, see the "ServerView Deployment Manager 5.0" manual (on PRIMERGY ServerView Suite DVD 2 under Industry Standard Servers -Software -ServerView Suite -Server Installation and Deployment). 5.3.1 Preparing for local installation Connect the monitor, mouse, keyboard and a DVD drive to the port on the server blade control panel with the aid of the special Y cable. See "Connecting devices" on page 37. I Make sure that the energy saving functions are disabled in the Power menu of the BIOS Setup during operation, and that the DVD drive has been activated as a boot medium. 5.3.2 Configuring the onboard SATA controller A SATA controller is integrated on the system board. You can configure the onboard SATA controller either before or during installation with the ServerView Installation Manager. Using the ServerView Installation Manager is recommended. 46 Operating Manual BX960 S1 Configuring the Server Blade I The controller has its own configuration utility. For further information, refer to the “Embedded MegaRAID Software User’s Guide” (on the ServerView Suite DVD 2 under Industry Standard Servers -Expansion Cards -Storage Adapters -LSI RAID / SCSI Controllers). I Descriptions of operating systems not covered in the controller manual are provided in the corresponding readme files on the driver CDs. 5.3.3 Configuring the server and installing the operating system with the ServerView Installation Manager Using the ServerView Installation Manager on the ServerView Suite DVD 1 provided, you can conveniently configure the server and install the operating system. This includes configuring the server-specific settings using the ServerView Configuration Manager and configuring the RAID controller using the ServerView RAID Manager. Advantages of the ServerView Installation Manager – Wizard assisted configuration of your server hardware and disk arrays – Wizard assisted installation of all leading server operating systems – Wizard-assisted creation of configuration files for unattended installation of several PRIMERGY servers with identical hardware configurations. – Installation ...

Download now

Please, enter two numbers from picture: