Votes - 0, Average rating: 0
(
)
)
|
manual abstract
Type 1: A constantly lit pixel (a bright, white spot), even though it is not addressed. A white pixel is caused when all three sub-pixel are lit. . Type 2: A pixel that does not light up (dark, black spot), although it is addressed . Type 3: Abnormal or defective red, green or blue sub-pixels. (E.g. constantly lit with half the brightness, one colour is not shining, blinking or flickering, but not belonging to Type 1 or 2 Pixel Failures) In addition: A cluster of type 3 (= 2 or more defective sub-pixels in an array of 5 x 5 pixel). A cluster is an array of 5 x 5 pixel (15 x 5 sub-pixel). ISO 13406-2, Class II Resolution Type 1 Type 2 Type 3 Cluster Type 1, Type 2 Cluster Type 3 1024 x 768 2 2 4 0 2 1280 x 854 3 3 6 0 3 1280 x 1024 3 3 7 0 3 1366 x 768 3 3 7 0 3 1400 x 1050 3 3 8 0 3 Example: A 17” - SXGA-display consists of 1280 horizontal and 1024 vertical picture dots (pixel), which amounts to a total of 1,31 million pixels. Based on one million pixels this translates into a factor of about 1.31. Class II type failure consequently allows for three defects each of type 1 and type 2 and 7 defects of type 3 and 3 cluster of type 3. These cases are normally not covered by warranty. If the number of failures exceeds the figures of any category mentioned above then this may be covered by the warranty. -90 UK/ N. IRELAND HELPLINE 0871 37 61 020 REP. IRELAND HELPLINE 1-800-992508 (calls are charged at 7p per min from a standard landline, calls from mobiles could be higher) FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: . Reorient or relocate the receiving antenna. . Increase the separation between the equipment and receiver. . Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. . Consult the dealer or an experienced technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Shielded interface cables, if any, must be used in order to comply with the emission limits. Appendix AidComponents Handling Safety -91 UK/ N. IRELAND HELPLINE 0871 37 61 020 REP. IRELAND HELPLINE 1-800-992508 (calls are charged at 7p per min from a standard landline, calls from mobiles could be higher) Index A All programs ................................. 20 Ambient Temperature ..................... 5 Appearance and Personalization ... 34 Audience .......................................... i Audio out ...................................... 46 Autorun ........................................ 64 B Battery operation .......................... 26 Battery power ........................... 28 Charging ................................... 28 Checking the battery level ......... 29 Discharging the battery ............. 28 Inserting .................................... 27 Removing .................................. 27 Battery Operation .......................... 10 Battery Power ................................ 28 BIOS Setup-Program ..................... 67 BIOS Utility Running .................................... 67 BullGuard Internet Security ........... 68 Cabling ........................................... 8 Care of Displays ............................ 84 Carrying out a Restore ................... 78 Charging the battery ..................... 28 Checking the battery level ............. 29 Connectors External monitor........................ 35 Power socket ............................. 15 Sound card ................................ 45 USB ........................................... 53 Control panel ................................ 60 Control Panel Disk Management ..................... 43 Customer service ........................... 80 D Data and system security ............... 73 Data entry ..................................... 38 Data security ............................. 4, 73 Directories ..................................... 44 Discharging the battery ................. 28 Display .......................................... 33 Opening and closing the display .................................. 33 Screen resolution ...................... 33 Driver Support .............................. 82 E ECO function Switch off ..............................