Votes - 0, Average rating: 0 ( )

Manafacture: Gigabyte File size: 2.1 mb File name: Language of manual:

4. Connect fan power connector to the CPU FAN connector on the motherboard. . . A. For IntelPentium4 processors CPU Pin Lever Apply thermal grease to the top of the CPU properly. Click the heat sink locker to the motherboard retention module. Install fan on top of CPU B. For AMD AthlonTM and AMD DuronTM processors Lever CPU Pin Apply thermal grease to the top of the CPU properly. P. E5 G-MAXG-MAX TM ATX Series User’s Manual Install fan on top of CPU motherboard retention module. Click the heat sink locker to the Set CPU clock frequency from BIOS Setup, see Motherboard Manual for details. ..Memory Notches at sides of module SDRAM Position notches. Make sure that the notches should align the pin on memory slot on the motherboard Notches at sides of module DDR Position notches. Make sure that the notches should align the pin on memory slot on the motherboard P. E6 G-MAXG-MAX TM ATX Series User’s Manual In this section we will guide you to install memory module. First, make sure the position notches at the bottom of the module should align to the pins on the module sockets on the motherboard, then push the module downward until the locks hook up notches at sides. Locks: make sure they hook up the notches at sides of module ..Hard Drive Installation 1.Remove 4 screws in front of the hard drive chassis and dismount chassis. HDD frame Press down splinter then pull out HDD frame. 2.The chassis accommodates up to six 3.5” storage devices. Select a place and fix the hard drive with screws. 3.5” floppy Drive HDD Drive HDD frame P. E7 G-MAXG-MAX TM ATX Series User’s Manual 3.Connect the IDE cable included in the accessory box to the connector on the hard drive. Make sure that the RED wire on the ribbon connects to PIN 1 of the hard drive. Connect to hard drive 4.Connect power connector to the hard drive. 5.Install chassis back to position after completing hard drive installation. HDD frame P. E8 G-MAXG-MAX TM ATX Series User’s Manual 6.Connect the other end of the IDE connector to the IDE-1 bus on the motherboard. 7.Check all connections again. Put back front Put back side panel panel P. E9 G-MAXG-MAX TM ATX Series User’s Manual V.System Installation and User’s Guide ..Front Panel Floppy LED *SPDIF CD ROM Tray CD-ROM Button Floppy Power LED Power Button Floppy Drive Audio Out HDD LED 1394 Hub Eject Button PCMCIA Button USB Port PCMCIA Port MIC In ..Rear Panel Power Inlet Voltage Switch Power Switch Keyboard Port (PS/2) Mouse Port (PS/2) COM Port LPT Port *COM Port / VGA Port Audio Out Game Port Audio In LAN Port MIC In USB Port 1394 Port P. E10 TM G-MAXATX Series User’s Manual ..Note 1.To avoid breaking disc during high-speed operation, we recommend you to use high quality CD/ Recordable CD/ Re-writable CD. 2.Specification with “..” mark are subject to change without notice. 3.For latest drivers update, please visit our Web site listed below: ..Important Safety Instructions Caution –To reduce the risk of fire, use only No.26 AWG or larger telephone line cord. Caution –Always disconnect all telephone lines from the wall outlet before servicing or disassembly this equipment. Caution –Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose used batteries according to the manufacturer’s instructions. P. E11 TM G-MAXATX Series User’s Manual -User’s Guide for SPDIF (For those models with SPDIF only) 1. Insert the Driver CD that was included in accessory box into your CD-ROM. Install or upgrade the audio driver. 2. If SPDIF can’t output normally after audio driver is updated, please operate step by step as below. (A)Click on Start Programs Accessories Entertainment Volume Control P. E12 G-MAXG-MAX TM ATX Series User’s Manual Select Enable Select (B)Volume Control Options Advanced Controls Select Add Properties Playback SPDIF OK P. E13 G-MAXG-MAX TM ATX Series User’s Manual Enable (C)Select SPDIF Advanced Sampling rate conversion for SPDIF output Close Finish 3. Similar procedures will be applied to different Windows® operating systems to enable the SPDIF function. P. E14 G-MAXG-MAX TM ATX Series User’s Manual For those models with SPDIF only -User’s Guide for Digital CD audio 1. Insert the Driver CD that was included in accessory box into your CD-ROM. Install or upgrade the audio driver. 2. If the digital CD audio can’t output normally after audio driver is updated, please operate step by step as below. (A) Click on Start Settings Control Panel (B) Select “System Properties” P. E15 G-MAXG-MAX TM ATX Series User’s Manual (C) Select Hardware Device Manager P. E16 G-MAXG-MAX TM ATX Series User’s Manual (D) Select DVD/CD-ROM drivers Properties (E) Select ”Enable digital CD audio for this CD-ROM device” OK P. E17 TM G-MAXATX Series User’s Manual (F) Select “YES” 3. The “Enable digital CD audio for this CD-ROM device” option in Windows® ME and Windows® XP is default set to “Enable”. 4. Similar pr...

Download now

Please, enter two numbers from picture: