Votes - 0, Average rating: 0
(
)
)
|
manual abstract
. . . . . . . . ......... ..1 ..... 1-1 ....... (........CPU) ...... .. AM2 CPU .. LGA775 CPU ..........,..... ...,....... ........,....... ......... . . . . ..........,..... ........ .CPU........,...CPU. ....... ..CPU........... .CPU.......,....... ,............. .CPU..........90..... .CPU...(.......)..... ......,..CPU.....,.. ............. ..CPU.....,......... .....,............ ...... ..3 ..2 AM2 CPU FAN . 3-pin LGA77.5 CPU FAN . 4-pin ......CPU....,... ....,CPU.....,... ......... ..1 ..........,........ ..........CPU........ (CPU_FAN),...CPU........ ... / ... ..1 ..... 1-2 ..... 1-3 ..... ..3 .....(...) ................. ......,.......... ..... PCI Express x1 .. PCI Express x16 .. ............,...... ........,.......... ..,............... PCI .. .........(....),.... ......... ....... ..............(.a) ..........(.b) ..........,..... ....... ......., ...(...). ..... ..............,.. ...,......... ..2 ..... 1..... 2...... 3........ 4.USB2.0. 5.......... 6...... 7........ 8.P/S 2... 9.P/S 2... 10.... 11..... 12.../.... 13.USB2.0. 14.IEEE1394. 15.USB2.0. 16.RJ45... 17...... 18...... 19.../..... 20.... 21..... 22..... (.a) (.b) ........,.......... ..............................PCI Express x16............. ......,..... ... ........,........ ........,....... .........,........... 24ME2-MED000-01R GB-MED-00............................................ Quick Installation Guide Components Introduction Step 1 Motherboard Installation .........................1-1 Installing the CPU Always turn off the computer and unplug the power cord from the power outlet before installing the all devcies to prevent hardware damage. Installing the CPU cooler Installing AM2 CPU Installing LGA775 CPU Apply an even and thin layer of thermal grease on the surface of the CPU. CPU socket lever Please refer to the cooler manual for detailed installation instructions. Completely raise the CPU socket lever, and remove the protective socket cover. Completely lift up the CPU socket locking lever. Align the CPU pin one (small triangle marking) with the triangle mark on the CPU socket and gently insert the CPU into the socket. Make sure that the CPU pins fit perfectly into their holes. Once the CPU is positioned into its socket, place one finger down on the middle of the CPU, lowering the locking lever and latching it into the fully locked position. Step 3 Step 2 LGA775 CPU FAN is 4-pin AM2 CPU FAN is 3-pin Step 1 Align the CPU pin one marking (triangle) with the pin one corner of the CPU socket (or you may align the CPU notches with the socket alignment keys) and gently insert the CPU into position. Replace the load plate and push the CPU socket lever back into its locked position. Do not force the CPU into the CPU socket. The CPU cannot fit in if oriented incorrectly. Adjust the CPU orientation if this occurs. Attach the power connector of the CPU cooler to the CPU fan header (CPU_FAN) on the motherboard. Step 1 Motherboard Installation 1-3 Installing a Memory Step 3 Installation of Optical Device (Card Reader) Front Panel / Rear Panel 1-2 Installing an Expansion card. Make sure the motherboard supports the expansion card. Carefully read the manual that came with your expansion card. PCI Express x1 slot PCI Express x16 slot Note the orientation of the memory module. Spread the retaining clips at both ends of the memory socket. Place the memory module on the socket. As indicated in the picture on the left, place your fingers on the top edge of the memory, push down on the memory and insert it vertically into the memeory socket. PCI slot Push the optical device (card reader) inward the trestle, then fixed by screws. Removing Expansion clip Press remove the screw on the expansion clip.(figure a) Open the clip on the rear panel.(figure b) Please connect with Hard Disk , Optical Device's (Card Reader) power connector. All the drawings in the guide are diagrams. About components's quantity and style, substances shall take precedence. A memory module has a notch , so it can only fit in one direction. 1. Power button 2. Microphone jack 3. Speaker or Headphone jack 4. USB 2.0 port 5. Voltage selector switch 6. Power Cord socket 7. Power Supply switch 8. P/S 2 Keyboard port 9. P/S 2 Mouse port 10. COM port 11. Display port 12. Printer port 13. USB 2.0 port 14. IEEE 1394 port 15. USB 2.0 port 16. RJ45 LAN port 17. Side speak out 18. Rear speak out 19. Center/Subwoofer speak out 20. Microphone 21. Front speak out 22. MIC in Step 2 Installation of Hard Disk For more product details, please click onto Gigabyte's website at (figure a) (figure b) Press the latch on the back of the white-drawable bar to release the card. 24................ME2-MED000-01R Unlock the drive tray by removing screw. Slide the hard disk drive onto empty slot, affix HDD by mounting 4 screws on each of drive bay. Gently push the drive tray handle toward to the close position and lock by screw. ...