Votes - 5, Average rating: 3.8
(
)
)
|
manual abstract
You may open the CD-ROM drive door by pushing the eject button located on the door of the drive. When the door opens, you can pull the tray out completely and clip in the CD onto the tray face up; then push the door in completely. The light on the CD door will light up while the CD-RPOM is being accessed. 2.3.8 Slim FDD Drive A floppy disk drive is essential as the floppy disk is still an important medium for transferring data between systems. Floppy disks are available in all computer stores and are usually ready for use if pre-formatted. You may insert the disk into the drive with the disk face up. During access to the floppy, the lights on the floppy disk drive will light up, indicating that the disk is currently being read from or written to. At this time you should not remove your floppy disk from the drive as doing so may cause damage resulting in data loss. Remove your floppy disk only when the drive light is off. Figure 2-8 2.3.9 LCD Display The LCD display has a self-locking mechanism. Pressing the lower right part of the LCD display toward the main chassis will release the display. You may adjust your portable to a comfortable viewing position by tilting the LCD display. To relock the LCD display, simply push the display back into its original position. Text Box: Floppy Text Box: CD-ROM Figure 2-9 2.3.10 Removable Cooling Fan The cooling fan on the right side can be easily removed. You don.t need to take off the back cover to replace the fan. Please see Chapter 5 for details. Figure 2-10 2.4 Installation Procedures 2.4.1 Card Installation and Removal The CompactPCI. connectors are firm and rigid, and you need to handle with care when plugging and unplugging. Improper installation of a card can easily damage the backplane of the chassis. The system card can be installed only in the system slot. Do not insert the system card into any other slot, or insert a peripheral card into the system slot. The system slot is marked by a triangle around the slot number (1). Please refer to the backplane user’s manual. The insert/eject handles on CompactPCI. cards help users to install and remove the cards easily and safely. Follow the procedures below to install a card into a chassis: To install a card 1. Hold the card vertically. Be sure that the card is oriented correctly. The components of the card should be pointing to the right side. 2. Be sure that the handles of the card are not latched. Release the handles if they are latched. Handles from different vendors may have different latch designs. Caution: Keep your fingers away from the latch hinges to prevent your fingers from getting pinched. 3. Insert the card into the chassis by sliding the edges of the card into the card guides. 4. Push the card into the slot gently by sliding the card along the card guide until the handles meet the rectangular holes of the cross rails. 1 2 Note: If the card is correctly positioned and has been slid all the way into the chassis, the handles should match the rectangular holes. If not, remove the card from the card guide and repeat step 3 again. Do not try to install a card by forcing it into the chassis. 5. Flip the handles out, and then push the card into position. The handles will click back into a horizontal position when the card is secure in the enclosure. 6. Secure the card by locking the handles into place. To remove a card 1. Unscrew the screws on the front panel of the card. Release the locking latches on the handles. 2. Push the red buttons on the up and down handles to release the card from the backplane. 3. Slide the card out. 2.4.2 Before Operating the System Before operating your system, check your power supply source. Adjust the switch on the power supply to the correct voltage. 2.4.3 Installing a 3.5. Hard Disk Drive Follow this procedure to install 3.5" hard disk drives in the CP-150: 1. Loosen the screws and remove the mobile rack. 2. Mount the HDD on the mobile rack, and fasten with screws. 3. Slide the HDD with mobile rack back into the tray and screw them. 4. Power on and check the HDD can be found when the SCSI is initialized. 2.4.4 Remove the Slot Unit Open back cover Unscrew the screws on the back cover. The screws are well-designed so they can.t easily be removed from the back cover. Prepare to remove the slot unit Figure 2-11 Text Box: PXI slot unit Text Box: Power supply Unscrew the upper cover of slot unit Text Box: Unscrew Text Box: Unscrew Pull the slot unit away Figure 2-12 2.4.5 Remove Drive Bay The whole 6U PXI slot unit Figure 2-13 Unscrew the fixed cover Figure 2-14 Unscrew the CD-ROM Figure 2-15 Text Box: Unscrew Remove the CD-ROM Figure 2-16 Unscrew the FDD Figure 2-17 Text Box: Unscrew Remove the FDD Figure 2-18 2.4.6 Remove the side-cooling fan Unscrew the cooling fan Figure 2-19 Remove the cooling fan Figure 2-20 2.4.7 Remove the Power Supply Unscrew & remove the side panel Figure 2-21 Remove the power supply with cover Figure 2-22 3 Backplane 3.1 General Information The backplane de...