Votes - 2, Average rating: 4
(
)
)
|
manual abstract
It calls attention to an operating procedure, practice, or the like that, if not correctly performed or adhered to, could result in damage to the product or loss of important data. Do not proceed beyond a CAUTION notice until the indicated conditions are fully understood and met. WARNING A WARNING notice denotes a hazard. It calls attention to an operating procedure, practice, or the like that, if not correctly performed or adhered to, could result in personal injury or death. Do not proceed beyond a WARNING notice until the indicated conditions are fully understood and met. U2761A User’s Guide Safety Symbols The following symbols on the instrument and in the documentation indicate precautions which must be taken to maintain safe operation of the instrument. Direct current (DC) Equipment protected throughout by double insulation or reinforced insulation Alternating current (AC) Off (supply) Both direct and alternating current On (supply) Three-phase alternating current Caution, risk of electric shock Earth (ground) terminal Caution, risk of danger (refer to this manual for specific Warning or Caution information) Protective conductor terminal Caution, hot surface Frame or chassis terminal Out position of a bi-stable push control Equipotentiality In position of a bi-stable push control U2761A User’s Guide General Safety Information The following general safety precautions must be observed during all phases of operation of this instrument. Failure to comply with these precautions or with specific warnings elsewhere in this manual violates safety standards of design, manufacture and intended use of the instrument. Agilent Technologies Inc. assumes no liability for the customer’s failure to comply with these requirements. WARNING • Do not operate the product in an explosive atmosphere or in the presence of flammable gases or fumes. • Do not use the equipment if it does not operate properly. Have the equipment inspected by qualified service personnel(s). CAUTION • Observe all markings on the instrument before connecting any wiring to the instrument. • Use the device with the cables provided. • Repair or service that is not covered in this manual should only be performed by qualified personnel(s). U2761A User’s Guide Environment Conditions This instrument is designed for indoor use and in the area with low condensation. The table below shows the general environmental requirements for this instrument. Environment conditions Requirements Operating temperature 0 °C to 50 °C Operating humidity 20 to 85% RH non-condensing Storage temperature –20 °C to 70 °C Storage humidity 5 to 90% RH non-condensing CAUTION The U2761A USB modular function/arbitrary waveform generator complies with the following safety and EMC requirements. • IEC 61010-1:2001/EN61010-1:2001 (2nd Edition) • Canada: CAN/CSA-C22.2 No. 61010-1-04 • USA: ANSI/UL 61010-1:2004 • IEC 61326-2002/EN 61326:1997+A1:1998+A2:2001+A3:2003 • Canada: ICES-001:2004 • Australia/New Zealand: AS/NZS CISPR11:2004 U2761A User’s Guide Regulatory Markings The CE mark is a registered trademark of the European Community.This CE mark shows that the product complies with all the relevant European Legal Directives. The C-tick mark is a registered trademark of the Spectrum Management Agency of Australia. This signifies compliance with the Australia EMC Framework regulations under the terms of the Radio Communication Act of 1992. ICES/NMB-001 indicates that this ISM device complies with Canadian ICES-001. Cet appareil ISM est confomre a la norme NMB-001 du Canada. This instrument complies with the WEEE Directive (2002/96/EC) marking requirement. This affixed product label indicates that you must not discard this electrical/electronic product in domestic household waste. The CSA mark is a registered trademark of the Canadian Standards Association. U2761A User’s Guide Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC This instrument complies with the WEEE Directive (2002/96/EC) marking requirement. This affixed product label indicates that you must not discard this electrical/electronic product in domestic household waste. Product Category: With reference to the equipment types in the WEEE directive Annex 1, this instrument is classified as a “Monitoring and Control Instrument” product. The affixed product label is shown as below: Do not dispose in domestic household waste To return this unwanted instrument, contact your nearest Agilent office, or visit: for more information. U2761A User’s Guide Declaration of Conformity DECLARATION OF CONFORMITY According to EN ISO/IEC 17050-1:2004 Manufacturer’s Name: Agilent Technologies Microwave Products (M) Sdn. Bhd Manufacturer’s Address: Bayan Lepas Free Industrial Zone, 11900, Bayan Lepas, Penang, Malaysia Declares under sole responsibility that the product as originally delivered Product Name: Agilent USB Modular Function Generator Models Number: U2761A Product Options: This declaration...