Votes - 3, Average rating: 5
(
)
)
|
manual abstract
++49(0)731-933-1340/1877 Fax ++49(0)731-933-1855 e-mail: info@AEGID.de Manual Page 3 / 33- Revision 01 ARE I2 / RS 232 – Installation Guide 6.7 BD- Baudrate 19 6.8 TOR – Maximum Reading Time 20 6.9 VS- Show Parameter 20 6.10 VSAVE – Save Parameter 20 7 OPERATING MODES OF THE READER 21 7.1 Mode 2 – Triggered by an Software Command 21 7.1.1 Settings of the Reader / Most Used Parameters 22 7.1.2 Basic Data Exchange Process 23 7.1.3 ReadOnly-Transponder 23 7.1.4 R / W –Transponder 23 7.1.4.1 Standard Read Process / Serial Number of the Transponder GT 23 7.1.4.2 Selective Read RD 24 7.1.4.3 Writing Process WD 24 7.2 Operating Mode 0 - Continuous Reading 26 7.2.1 Settings of the Reader / Most Used Parameters 26 8 INSTRUCTIONS 28 8.1 General Instructions 28 8.2 Special Instructions for Using a Read / Write System 29 9 HOTLINE 30 10 REFERENCE DOCUMENTATION 30 11 REVISIONS 30 12 APPENDIX 31 12.1 Best Orientation for an F-Type -Reader 31 12.2 Best Orientation for an L-Type -Reader 32 12.3 Assembling of the SAB Cab 33 AEG Identifikationssysteme GmbH Soflinger Stra.e 100 D-89077 Ulm Tel. ++49(0)731-933-1340/1877 Fax ++49(0)731-933-1855 e-mail: info@AEGID.de Manual Page 4 / 33- Revision 01 ARE I2 / RS 232 – Installation Guide AEG Identifikationssysteme GmbH Soflinger Stra.e 100 D-89077 Ulm Tel. ++49(0)731-933-1340/1877 Fax ++49(0)731-933-1855 e-mail: info@AEGID.de Manual Page 5 / 33- Revision 01 ARE I2 / RS 232 – Installation Guide 1 Introduction This document will describe the components of the Compact Reader System ARE I2 / RS 232 and the procedure how to do the first set up of the reader. The main features of the reader are listed below: • the antenna is placed inside of the housing (base version) • there are algorithm available to read nearly all 125 kHz-transponders on market • the serial RS 232-Interface is placed inside of the housing, allowed baud rate are up to 19200 Bit/s • the allowed supply voltage is 9 to 30VDC • low power consumption of reader < 1.2 Watt • high reliability for reading and writing within an industrial environment. • compact housing of the reader with multiple ways for mounting. • the cabling concept of the reader is optimised to service demands. • the protection class of the housing is IP65 • there is a set of external antennas available to meet special application demands ( X-tended version) 2 System Overview In the base version all electronic components of the reader is placed inside of a small plastic housing. RS232(9-Pin SubD) Transponder Reader with Integrated Antenna ARE I2 24VDC Figure 2-1: Concept of the Reading System AEG Identifikationssysteme GmbH Soflinger Stra.e 100 D-89077 Ulm Tel. ++49(0)731-933-1340/1877 Fax ++49(0)731-933-1855 e-mail: info@AEGID.de Manual Page 6 / 33- Revision 01 ARE I2 / RS 232 – Installation Guide The connection of the cables (power supply and data transfer) is done inside of the connection cab (SAB Cab). Together with an sealing element a protection classification of IP 65 is guaranteed. By means of the integrated antenna the reader generates an alternating magnetic field, which powers the transponder. Coded signals sent back from the transponder are received and decoded by the reader The reader is fully controlled by an Master with RS 232 data port, while using the integrated serial RS 232 Interface of the reader. The side of the housing showing the antenna symbol must not be brought next to a metal surface. This could lead to a significant change of the properties of the antenna circuit, which in turn reduces the reading range considerably. Environmental electromagnetic noise may also reduce the specified reading performance. Special hints to overcome these problems are documented in Chapter 8. Start-up Procedure The start-up procedure of the reader system is split up to following steps: • mounting of the reader and pin connection (cabling), see Chapter 4 • operational instructions, see Chapter 7 To get a feeling how the IdentSystem will work, first start the reader controlled by the serial interface (RS 232) of an isolated PC. The next step is to integrate the reader to the operating network. AEG Identifikationssysteme GmbH Soflinger Stra.e 100 D-89077 Ulm Tel. ++49(0)731-933-1340/1877 Fax ++49(0)731-933-1855 e-mail: info@AEGID.de Manual Page 7 / 33- Revision 01 ARE I2 / RS 232 – Installation Guide 4 Installation To get the specified reading performance it is necessary to do the installation carefully step by step as it is described in the following Chapters. All the work must be done by well educated people. 4.1 Mounting of the Housing The reader can be mounted to any other mechanic construction. It is recommended to protect the housing against heavy mechanical interactions. Attention! The side of the housing showing the antenna symbol must not be brought next to a metal surface. This could lead to a significant change of the properties of the antenna circuit, which in turn reduces the reading range considerably. With the help of the plastic bars, th...