Votes - 2, Average rating: 3 ( )

Manafacture: Grindmaster File size: 429.12 kb File name: Language of manual:

3. Use the up and down buttons to make your adjustments to the settings, then press the select button again to store your new settings. The display will flash to indicate your settings have been stored. Scroll through settings to confirm timer setting gives desired dispense volume. a.) Brew a pot to confirm timesetting gives desired dispense volume. b.) Record your new timer values on the customer settings chart located on time face. 4. After a few seconds, the display will shut itself off. The access panel may be re-installed. Figure D GRIND’N BREW Timer settings/ with new PDS Flow control valve A standard 1,9L bottle Grind’n Brews All Airpot Grind’n Brews Setting Single Bean Approx yeild Setting Dual Bean Approx yield Single/Left Full Pot 4.2 secs 2 oz./6ml 5.7 secs 2 oz./5.8ml Right Full Pot --5.7 secs 2 oz./5.8ml Single/Left Half Pot 2.4 secs 1.25 oz./4ml 3.0 secs 1.25 oz./3.6ml Right Full Pot --3.0 secs 1.25 oz./3.6ml Full Pot 112-125 secs 62 fl oz./180ml 112-125 secs 62 fl oz./180ml Half Pot 56-63 secs 31 fl oz./90ml 56-63 secs 31 fl oz./90ml Setting Single Bean Approx yeild Setting Dual Bean Approx yield Single/Left Full Pot 4.5 secs 2.3 oz./7ml 6.2 secs 2.3 oz./7ml Right Full Pot --6.2 secs 2.3 oz./7ml Single/Left Half Pot 2.7 secs 1.4 oz./4ml 3.7 secs 1.4 oz./4ml Right Full Pot --3.7 secs 1.4 oz./4ml Full Pot 140-153 secs 72 fl oz./209ml 140-153 secs 72 fl oz./209ml Half Pot 70-77 secs 36 fl oz./104ml 70-77 secs 36 fl oz./104ml English • Increase of 1 second to timer setting equates to an increase in fluid volume by 1/2 ounce/1.5ml. • Decrease of 1 second to timer setting equates to a decrease in fluid volume by 1/2 ounce/1.5ml. Page 5 Grind ’n Brew Coffee Systems Setting Grind: Tool Required: #2 Phillips screwdriver, 7/8"/2.2cm box wrench, large flat blade screwdriver 1. Remove front decal panel by removing screw on underside of panel. 2. Loosen adjusting screw lock nut by turning counter clockwise. 3. Turn slotted adjusting screw clockwise to make the grind coarser or counter clockwise to make the grind finer. (See Figure E) Generally, a 1/8 to 1/4 turn will provide desired adjustment. 4. After adjustment has been made, re-tighten adjusting screw lock nut. 5. Visually inspect grind adjustment with a small portion of coffee and readjust if necessary. 6. Reinstall the front decal panel as it was removed. REGULAR MAINTENANCE Note : Machine should not be cleaned with a pressure sprayer. This could result in a Figure E shock hazard. Daily Cleaning Cabinet : The outside of the machine can be cleaned with a damp cloth, a household dusting spray or a stainless steel cleaner. Do not use an abrasive such as Scotchbrite or Brillo pads. These may mar the finish. Wipe the underside of the cabinet hood with a clean cloth. Be especially careful when using soap or detergent around the sprayhead. Any soap left on the deflector may impart an unpleasant taste to the first brews. Warmers : The warmer plate is easy to clean and will maintain its appearance longer if cleaned regularly. Coffee stains can be wiped off with a damp cloth. Use detergent or sanitizer for heavy deposits, but refrain from using abrasives. Weekly Cleaning Slide Valve: The slide valve behind the spray deflector under the cabinet hood should be wiped off with a clean, dry cloth. Using the finger tab (Figure F) open the slide valve. Note: When the machine is not in use, the finger tab will automatically activate every 30 minutes to keep clear. Brew Basket, Airpots and Decanters: Use commercial grade urn cleaner (as directed by manufacturer) and rinse thoroughly. Figure F English Page 6 Grind ’n Brew Coffee Systems SHEAR PLATE REPLACEMENT Tools Required: #2 Phillips Screwdriver, Large flat blade screwdriver 1. Unplug machine. 2. Remove front panel and hopper. To remove hopper, pull bean shut-off valve forward. This will shutoff the flow of coffee beans and allow you to lift it from the grind head. 3. Remove hopper cradle. There are 5 screws (2 in front and 3 across back) holding the hopper cradle in place. Loosen screws and lift up hopper cradle. 4. Remove spray head. First remove the spray deflector by spinning Figure Git clockwise. Second, pull the spray nozzle away from mounting sheet. 5. Remove grind cap by loosening the 2 screws and rotating the grind cap away from the screws. 6. Pull out the revolving burr and freedworm assembly. The sweeps on the revolving burr must line up with the cut outs on the grind head. (See Figure G). 7. Remove the shear cap and broken shear plate. 8. Slide the rotating burr onto the motor shaft, aligning up the sweeps with the cutouts on the grind head. Rotate the burr so that the burr is held back into the burr pocket by the sweeps on the grind head lip. Slide the drive coupler into place. Rotate the slot on drive coupler with the feed worm. Insert a new shear plate. Shear disc 9. Reassemble the remaining components in reverse order of disassembly. plate WATER SOLENOID VALVE (See Figure H) English Tools Required: ...

Download now

Please, enter two numbers from picture: