Votes - 4, Average rating: 4.5 ( )

Manafacture: Capresso File size: 96.56 kb File name: ref_z5.pdf Language of manual:

Watch the DVD instructions! Traces of Coffee Grounds in New Machine? This is normal! Grinder was tested during assembly with beans. Despite cleaning, traces of ground coffee may be found. RED TEXT represents display text. Illustration numbers on next page correspond with Operating Instructions. A) First Time Ever Preparation 1. Fill water in tank, open Cover Lid (spring activated!), remove Bean Container Safety Lid and add beans. Only regular beans, no flavored or coated beans!!! Replace Bean Container Safety Lid (Fig. 4). 2. DO NOT install the Clearyl Filter Cartridge now! 3. Turn the Main Power Switch on (bottom left by cord). 4. Push On/Off button on top (Fig. 3). Place a large cup under the Hot Water Spout / Coffee Spouts and one under the Auto Cappuccino System (ACS) (Fig. 5e). PRESS RINSE. Push the Rinse button. SYSTEM FILLS, then WELCOME TO JURA then UNIT IS HEATING then PRESS RINSE. Press the Rinse Button. COFFEE READY. 5. Leave the cup under the coffee spouts and push the 1-cup Espresso Button. FILL BEANS. Push the 1-cup Espresso Button again. Wait until the Z5/Z6 displays COFFEE READY. Discard the coffee. 6. Your next cup will be perfect. B) Daily Preparation • Fill fresh water in tank and check bean container. • Push On/Off button (Fig. 3). MACHINE IS HEATING then RINSE. Place a cup under the coffee spouts and press the Rinse Button. COFFEE READY. C) Installing the Auto Cappuccino System (ACS) • Attach the Dial Component to the Dual Fixed Spouts. (Fig. 5c) 65351R2 Rotary On/Off Dial Rinse COFFEE READY Milk Cappuccino Special Hot 1-Cup 2-Cup 1-Cup 2-Cup Latte Coffee Water Espresso Coffee Fig. 3 Bean container safety lid Lid for ground coffee Grind selector Fig. 4 Cover lid Fig. 5c Fig. 5d Fig. 5e Gap Coffee Nozzle Milk Nozzle Fig. 5fMilk & Froth (Cappuccino) Milk only (Latte) Steam only (Rinsing) ACS Venting tip • Then attach the long Dual Nozzle System to the Dial component (Fig. 5d). Please note: The milk nozzle should sit tight. The coffee nozzle must have a gap (Fig. 5e). Make sure the dial points to the cup with saucer for cappuccino (Fig. 5f). • Attach the long hose to the dial component and insert the other end into a milk carton. Thermal Milk Container: If you use the thermal milk container, attach the straight rod to the lid with the tapered end pointing to the bottom. Then insert the elbow rod through the top of the lid into the straight rod. Slip the open end of the short flexible hose over the elbow rod. Fill the thermal container with cold milk and assemble lid, thermal container and dial component. Important: Cold milk will stay cold for about 8 hours in the thermal milk container. Then the milk must be returned to the refrigerator or discarded. Remove lid when refrigerating. Rinse hoses and thermal container with hot water. D) Eight Beverage Buttons The Milk, Cappuccino and Special Coffee button brew through the ACS System (Fig. 5e). The Hot Water button brews through the hot water spout. The beverage buttons are pre-set as follows: Button Function Milk Coffee Volume Coffee Strength Milk Cappuccino/Latte Special Coffee Hot Water 1 Espresso 2 Espresso 1 Coffee 2 Coffee * * * * * * 20 sec 15 sec – – – – – – – 3.0 oz 3.0 oz. 6.0 oz. 1.5 oz. 3.0 oz. 5.0 oz. 10.0 oz. – NORMAL XSTRONG – STRONG STRONG NORMAL NORMAL * Temperature for coffee is set at HIGH. • You can override Coffee Strengths just before brewing. • You can override Cup Size during brewing. • Overriding (chapter M) will not change above pre-sets. • All pre-sets can be changed to new pre-sets (chapter N) Important: You can always stop any brewing by pushing the Rotary Dial or any beverage button. Important: Never try to pull out the drawer while the Z5/Z6 is brewing or discarding. Always wait until the cycle is completed and the display shows COFFEE READY. E) Cappuccino and Latte COFFEE READY Place a cup under the ACS. The dial points to the cappuccino setting and the hose connects to the dial component and is inserted into cold milk. Push the Cappuccino Button. CAPPUCCINO then MILK 15 SEC then 3 OZ. NORMAL. For 15 seconds hot frothed milk is produced, coffee is ground, tamped and 3 oz. of high pressure coffee is added. After the used coffee is discarded the display returns to COFFEE READY. For Latte (steamed milk without froth) turn the dial to the tall glass (Fig. 5f) and use the same button. F) Hot Chocolate / Hot Milk COFFEE READY Proceed as under E. Start with cold chocolate milk or dissolve chocolate syrup in cold milk. Push the Milk Button. MILK 20 SEC then COFFEE READY. G) Cappuccino Rinsing CAPPU RINSE Ten minutes after last using milk the display shows CAPPU RINSE. You can still make coffee. Place a cup under the ACS system. Push the Rinse Button. CAPPUCCINO RINSING. COFFEE READY. Daily ACS Cleaning with Cappuccino Cleaner Liquid. Remove all frother parts (dial component, nozzles, venting tip, hoses and lids that come in contact with milk). Place in a cup with fresh water. Add 15ml of the Cappu Cleaner Liquid. Within...

Download now

Please, enter two numbers from picture: