Votes - , Average rating: ( )

User manual Sunbeam, model EM3600

Manafacture: Sunbeam
File size: 2.56 mb
File name: 5061515b-85a1-4eb5-9d77-0755f56b1149.pdf

Language of manual:

The document is loading, please wait

Download nowClose

The document is loading, please wait

Download nowClose

Therefore the espresso machine will require occasional descaling. It is recommended that the espresso machine is descaled every 4-6 months, this will vary depending on the frequency of use. Descaling solution Use any of the following when descaling the espresso machine: . Sunbeam Espresso Machine Descaling Tablets . Sunbeam Liquid Descaler, or . Vinegar Solution. Descaling the espresso machine Note: Ensure the espresso machine is turned off and the power cord is unplugged. 1. Remove the water reservoir and rinse clean. Depending on the descaling solution being used use one of the following: A. Sunbeam Espresso Machine Descaling Tablets Fill the water reservoir with 1 litre of warm water and place a descaling tablet into the reservoir. Once the tablet has dissolved replace the reservoir, this takes about 5-7 minutes. B. Sunbeam Liquid Descaler Fill the water reservoir with approximately 1.5 litres of water, add 1 capful of Sunbeam Liquid Descaler and replace the reservoir. C. Vinegar solution Fill the water reservoir with approximately 1.5 litres of warm water, add 3 tablespoons of vinegar and replace the reservoir. 2. Should the filter handle be attached to the group head remove it, rinse thoroughly under running water and set aside. 3. Using a screwdriver unscrew the brewing filter/shower screen from the underside of the group head. 4. Remove and set aside the filter/screen, washer and screw in a safe place. Important: Be careful not to lose the filter/ screen, washer and screw once you have disassembled the group head. 5. Using a small brush scrub in and around the area at the brewing head, removing all coffee granules. 6. Place a sufficiently large container under the group head. 7. Insert the power cord into a 230-240V AC power outlet and switch the power ‘ON’. Press the power switch to turn the espresso machine on. Note: Remember if the 'HEATING' light is on the espresso machine is adjusting the temperature of the heating system. Once the espresso machine is heated to the correct temperature, 'HEATING' light will go off, this indicates that the espresso machine is heated and ready to use. 8. Turn the operating dial clockwise to the espresso setting and allow half the solution to cycle through the group head. Important: Do not run descaling solution through the steam wand. Note: Depending on the size of the container under the group head on occasion this may need to be emptied throughout this process. 9. After half the solution has cycled through turn the operating dial to the off position to stop the flow and then press the power switch to turn the machine off. 10. Leave the machine off for 10-15 minutes to allow the descaler solution to take affect. 11. Press the power switch to turn the espresso machine on. 12. Turn the operating dial to the espresso setting and allow the remaining solution to cycle through the group head. 13. Remove the water reservoir from the machine and rinse thoroughly under running water, ensuring that all traces of the descaling solution is removed. Fill with clean water and replace the reservoir. 14. Turn the operating dial to the espresso setting and allow the entire water reservoir to cycle through the group head. Note: Depending on the size of the container under the group head on occasion this may need to be emptied throughout this process. 15. When this is finished remove the container under the group head and give the machine a good wipe over. 16. Carefully replace the rubber seal, brewing filter/shower screen and washer to the group head. Tighten well. 17. Fill the water reservoir with fresh water and position it on to the machine. Descaling (continued) Trouble Shooting guide PROBLEM POSSIBLE CAUSE WHAT TO DO Coffee runs down the side of Filter handle is not attached correctly, Ensure the handle is firmly positioned the filter handle. or has not been tigtened sufficiently. onto the group head. See “Guide to the perfect espresso” pg 15. Edge of filter insert is not free Clean around the top edge of the of coffee granules. filter and wipe the group head clean of coffee. The group head is dirty. Wipe group head with a damp cloth. The group head is defective. Contact a Sunbeam Service Centre. Group head rubber seal is damaged, Contact a Sunbeam Service Centre. or warn. No coffee runs through. No water in the water reservoir. Fill reservoir with water. Water reservoir not correctly Press firmly down on the water reservoir assembled. to ensure it is correctly positioned. Operating dial set to Ensure the operating dial is in the setting. espresso position. Group filter may be blocked. See “Descaling” pg 22. The filter is blocked, the coffee Empty out the filter and rinse under grounds are too fine or tamped water to clean. Wipe the group head down too hard. with a cloth and use a coarser coffee grind. Coffee pours out in drops. Coffee grind is too fine or are Use a coarser grind and ensure the too compacted. filter basket is not over filled. Machine blocked by scale build up....