Coffee can be brewed directly into the server without removing the cover when used with an appropriate Bunn® coffee brewer. Place the server on a warming stand to keep the beverage hot at remote locations. The spill-resistant design lessens the chance of hot beverage burns and splashes. USER NOTICES The notices on this server should be kept in good condition. Replace unreadable or damaged labels. CLOSE REMOVE ONLY FOR DAILY CLEANING OPEN #12373.0000 #12356.0000 USING THE SERVER 1. Lock the cover

The spill-resistant design lessens the chance of hot beverage burns and splashes. USER NOTICES The notices on this server should be kept in good condition. Replace unreadable or damaged labels. CLOSE REMOVE ONLY FOR DAILY CLEANING OPEN #12373.0000 #12356.0000 USING THE SERVER 1. Lock the cover in place on the server by turning it clockwise as far as it will go. 2. Locate the center of the server cover directly under the funnel dripout of a Bunn® coffee brewer when brewing directly into the serve

Continuity must be present when the door is closed. Continuity must not be present when the door is open. 4. Reconnect the twelve pin connector to the control board. 5. Gain access to the door switch using steps listed in Removal and Replacement. 6. Disconnect the wires from the door switch. 7. Check continuity between the N.O. and COM. terminals of the switch using an ohmmeter. Continuity must be present when the actuator is engaged. Continuity must not be present when the actuator is released.

USER NOTICES Carefully read and follow all notices on the grinder and in this manual. They were written for your protection. All notices on the grinder are to be kept in good condition. Replace any unreadable or damaged labels. KEEP FINGERS ANDFOREIGN OBJECTSOUT OF HOPPEROR CHUTE OPENING. PERSONAL INJURYHAZARD. #05876.0000 #37881.0000 #20545.0000 00824.0002 27091.1 040612 ELECTRICAL REQUIREMENTS The grinder has an attached cordset and requires 2-wire, grounded service rated 230 volts ac, 10 amp

Adequate space must be available above the grinder to raise the lid when adding beans. Use only with whole bean coffee. The grind is preset at the factory to drip specifications as set forth by the United States Department of Commerce and adopted by the Coffee Brewing Center of the Pan American Coffee Bureau. Adjustments may be made to alter both the amount and grind from the factory setting. USER NOTICES Carefully read and follow all notices on the grinder and in this manual. They were written

THE BUYER’S REMEDY AGAINST BUNN FOR THE BREACH OF ANY OBLIGATION ARISING OUT OF THE SALE OF THIS EQUIPMENT, WHETHER DERIVED FROM WARRANTY OR OTHERWISE, SHALL BE LIMITED, AT BUNN’S SOLE OPTION AS SPECIFIED HEREIN, TO REPAIR, REPLACEMENT OR REFUND. In no event shall BUNN be liable for any other damage or loss, including, but not limited to, lost profits, lost sales, loss of use of equipment, claims of Buyer’s customers, cost of capital, cost of down time, cost of substitute equipment, facilities o

If continuity is present as described, proceed to #4. If continuity is not present as described, replace the switch. 4. Check for continuity across the .25" terminals of the switch when it is in the “ON” position. Continuity must not be present in the upper “OFF” position. If continuity is present as described, reconnect the wires, the switch is operating properly. If continuity is not present as described, replace the switch. Removal and Replacement: 1. Remove all wires from the switch terminal

(2.72 kg) of fresh coffee beans. • Easy access on back for grind weight adjustment. • Three-year warranty on grinding burrs. • International electrical configurations available. Model LPG (funnel not included) Dimensions: 15.1” H x 8.64” W x 10” D (38.4cm H x 21.95cm W x 25.4cm D) For current specification sheets and other information, go to Related Products Precision Burrs All BUNN grinders use precision burrs to cut (not crush) the coffee beans and deliver consistent grind distributio

Hopper Selector Switch (Model LPG-2E only) LEFT - Switching to this position allows beans to be ground from the left hopper. RIGHT - Switching to this position allows beans to be ground from the right hopper. P1028 P1029 PREVENTIVE MAINTENANCE Bunn-O-Matic® Corporation recommends that preventive maintenance be performed at regular intervals. Maintenance should be performed by a qualified service technician. For Technical Service, contact Bunn-O-Matic® Corporation at 1-800-286-6070. NOTE: Replace

This allows for precise dispensing of various flavors of products. Programming of the dispenser is achieved by entering a certain function, then, by use of programming switches, the operator can customize the dispensing process to their specifications. To access the programming mode, and to scroll through different function screens, the programming switches shown are used. There are five switches that will be used for setup of the dispenser. A. Enter program mode and advance to next menu B. Incr