Votes - 2, Average rating: 4 ( )

Manafacture: Breckwell File size: 567.94 kb File name: P2000_2005_Manual.pdf Language of manual:

If only the 1 light is on, the stove is in the default (medium) setting. If the 1 & 4 lights are on, the stove is in the high trim setting for the low feed rate. If the stove is being burned on one of the two lower settings, advance to the next trim setting and try burning the stove. 28 8 TROUBLESHOOTING GUIDE HIGH LIMIT SWITCH KEEPS TRIPPING Possible Causes: Possible Remedies: 1. The convection blower is overheating and tripping the internal temperature shutoff. Clean any dust off of the windings and fan blades. If cleaning the blower does not help, it may be bad. 2. The stove is being left on the highest setting for extended periods of time. The highest heat level setting is designed for use over short periods of time. Burning the stove on the highest setting for longer than 1 – 2 hours could lead to potential overheating situations. 3. Fuel other than wood pellets is being burned in the stove. Breckwell pellet stoves are designed and tested to use wood pellets. While it is possible to burn a corn mixture (corn mixed in with wood pellets) in the stove, it is not recommended to burn above the number 3 heat level. Check for signs of fuel other than wood pellets. If there are signs of corn being used, find out what mixed was being used and what setting. No other types of fuel have been approved for Breckwell pellet stoves. If there are signs of other types of fuel being used, advise the consumer to stop using them immediately. 4. Power surge or brown out situation. A power surge, spike, or voltage drop could cause the high limit switch to trip. Check to see if a surge protector is being used on the stove. If not, recommend one to the consumer. 5. High limit switch is malfunctioning. If the other items check out ok, replace the high limit switch. DIGITAL CIRCUIT BOARD TIMING RATES Heat Level Setting P2000 1 & 3 1.4 seconds 1 2 seconds 1 & 4 2.5 seconds 2 4 seconds 3 7 seconds 4 9 seconds 5 12 seconds Total Cycle Time 14.5 seconds SMOKE SMELL OR SOOT BUILD-UP Because it is a wood-burning device, your Breckwell may emit a faint wood-burning odor. If this increases beyond normal, or if you notice an unusual soot build-up on walls or furniture, check your exhaust system carefully for leaks. All joints should be properly sealed. Also clean your stove, following instructions in “MAINTENANCE”. If problem persists, contact your dealer. ELECTRICAL DIAGRAM FIGURE 29 29 ELECTRICAL DIAGRAM FIGURE 29 29 REPLACEMENT PARTS30 REPLACEMENT PARTS30 Contact an Authorized Breckwell Pellet Stove Dealer to obtain any of these parts. Never use substitute materials. Use of non-approved parts can result in poor performance and safety hazards. ITEM PART # Air Switch C-E-201 Air Switch Hose C-M-340-T Auger Motor C-E-017 Breckwell Maintenance Tool A-TOOL-96 Brick Panel Set, Ceramic – Optional A-M-BRICK2000 Burnpot A-S-BURNPOT Circuit Board / Control Panel C-E-401 Combustion Blower A-E-027 Convection Blower A-E-033 Door Gasket C-G-050 Door Glass – Center C-D-802-A Door Glass – Side C-D-802-B Exhaust Adapter 3” C-M-020 Exhaust Adapter 4” A-4-VA Hot Rod Igniter C-E-IGN Remote Thermostat – RF – Acumen - Optional AG-RCN Thermodisk, Proof of Fire C-E-090-22C Thermodisk, High Temp C-E-090-21 Door Handle - Wood C-S-852 Damper Knob - Wood C-S-851 Window Gasket (7’) C-G-033 Ceramic Log Set (imitation) - Optional A-M-2000 Zero Clearance Skirt - Optional A-ZC-2KSKRT Zero Clearance Legs – Optional A-S-ZCLEGS LIFETIME LIMITED WARRANTY Breckwell Hearth Products warrants to the original consumer purchaser that the Breckwell stove in its original installation is free from defects in material and workmanship from the original date of purchase as follows: Steel fabricated components, excluding burnpot inserts, are covered for five years. Glass and burnpot inserts are warranted for one year only for thermal damage. Electrical components, which include the digital control board, auger motor, combustion and convection blowers, igniter, and valves, are covered for one year. There is no warranty on gaskets or paint. After expiration of the warranty period, any components may be purchased at 30% discount off manufacturers suggested list price plus shipping and handling charges, as long as the original consumer purchaser owns the product. This warranty covers defect in materials and workmanship in covered components, provided this product has been properly installed and operated strictly in accordance with the instructions in this owner’s manual and any applicable local codes. This warranty does not cover damage or breakage caused by improper maintenance, handling, misuse, abuse, overfiring, disassembly, unauthorized modification or other circumstances beyond Breckwell’s control. If warranty service is needed during the warranty period, contact your Authorized Breckwell Dealer. Provide your name, address, phone number, serial number and model number of the stove, date of purchase, name and address of installer and as much information as possible about the nature ...

Download now

Please, enter two numbers from picture: