Votes - 3, Average rating: 4.3 ( )

Manafacture: Hearth and Home Technologies File size: 1.65 mb File name: Language of manual:

Slide assembled trim over panel set. See Figure 12B. Figure 12A Figure 12B Adjust position by sliding left or right after top is in place. Install sides and push out to maximum distance of slot. Panel brackets DOOR HANDLE ASSEMBLY 1. Install washer on door handle shaft. . Slide door handle through door. 3. Install second washer(s) as shown. 4. Install key in groove. 5. Align groove in latch cam with key; slide latch cam over shaft. 6. Install locknut. Caution! Do not overtighten locknut. Door handle needs to move smoothly. 7. Install spring handle turning counter- clockwise to desired location on handle. Locknut Door Cross Section (example)Latch Cam Spacing Washers Square Key Door Handle Spring Handle View of “L” Bracket Installed Page 12 250-6381D September 1, 2008 September 1, 2008 Page 13 3100-I ACT WOOD INSERT R 250-638D Included in Kit: (2) Fan mounts & fan assemblies; (1) Speed Control, Power Cord/wire assembly; (1 set) Fan Connector wires, must be high temperature wire; and (1) Strain relief. Tools Needed: Large Phillips screwdriver, pliers FAN (BLOWER) INSTALLATION INSTRUCTIONS Part No. 831-1101 Power Cord Speed Control Feed Fan Motor Wires Through Holes Strain Relief Location, Holding Together Power Cord and Fan Motor Wires Screens (Fan Covers) Black & White Wires Attach to Fan Motor Terminals Power cord can be attached to the right or left side. 1. Remove Screens (fan covers). 2. Install fan mounts to outer wall with panel mounting screws. 3. Feed fan and motor wires up through large hole in floor. NOTE: Power cord can be mounted on left or right side. 4. Connect white and black wires to fan motor terminals and the green ground wire to ground terminal 5. Feed fan motor wires through holes in bottom and across to the other fan motor. 6. Install strain relief onto power cord. 7. Using a pair of pliers, squeeze strain relief and push through hole. 8. Plug in and test blower operation. 9. Replace Screens. 10.Route power cord away from the unit. DO NOT route power under or in front of unit. NOTE: When the speed control is turned clockwise, it will click on to high speed. Continue to turn the speed control clockwise to decrease the speed. At full clockwise, the blower should blow gently, but should not stop. 1. With the unit plugged in, turn the Speed Control Knob to slow. (Full clockwise.) 2. Use a small screwdriver to adjust the fan speed by turning the adjustment mechanism through the hole on the side of the Speed Control. 3. Adjust the speed so the fan runs slowly but does not stop. Turn clockwise to slow the fan and counterclockwise to increase the speed. FAN SPEED CONTROL ADJUSTMENT, IF NECESSARY* *The fan Speed Control for this unit is adjusted at the factory, and normally does not require further adjustment. RR 3100-I ACT WOOD INSERT ZERO CLEARANCE ADJUSTABLE TRIM SUPPORT, 2” to 10” Part No. 841-0990, size 9” x 45” and Part No. ADJSPT-12, size 12” x 50” Included in Kit: (1) Trim Top, (1) Trim Front, (2) Trim Sides, Double-Sided Tape (already installed) Tools Needed: Phillips Head Screwdriver, Sheet Metal Shears, Measuring Tape, Gloves 1. The 10 screws on each set of scissors will already be loose when shipped. See Figure 14A. 2. Expand scissors to desired height. Tighten screws to hold in place using Phillips Head screwdriver. See Figure 14B. 3. Measure front and side trims to required height to cover scissors and mark pieces for cutting. Cut excess material from top of trim’s edge, not bottom. This edge will be sharp; wear gloves to prevent injury to your hands. See Figure 14B. 4. Using sheet metal shears, cut trim along the marked edge. The cut edge fits under lip of top trim, so it allows for some variance in your straight edge. 5. The double-sided tape that holds front and side trims to scissors has a particularly powerful bonding adhesive. Adjustments are extremely difficult once trim has adhered to tape. Do a dry run first without removing paper from tape. 6. Place cut edge of trim under top lip and into position on scissors. Place side pieces on first and then front piece. The front piece overlaps side pieces. NOTE: The trim in the Flush Mount Kit is one piece. 7. Once you are satisfied with the positioning, remove trim and set aside. 8. Remove the paper from double-sided tape that is to accept trim side. Align side and then press hard against tape to secure side piece. Repeat for other side. Install front trim piece last. 9. There are 3 holes in the back flange of the top to secure it to the wall if necessary. Use the appropriate fastener for the type of wall material, i.e., brick, sheetrock, etc. NOTE: 3/8” ( 9.5mm) thick tile or like material can be cut to size and fit under lip of top trim edge for a decora tive touch. See Figure 14C. EXPLODED VIEW OF SCISSORS SCREWS ARE CIRCLED DOUBLE-SIDED TAPE DOUBLE-SIDED TAPE Figure 14A EXPAND SCISSORS TO DESIRED HEIGH T CUT TOP EDGE OF TRIM, INSTALL FRONT TRIM LAST. NOT BOTTOM EDGE CORNERS OVERLAP SIDE TRIM PIECES Figure 14B Figure 14C Decorativ...

Download now

Please, enter two numbers from picture: