Login:
Votes - 4, Average rating: 3.5 ( )

User manual Lennox Hearth, model SLDVT-45NM

Manafacture: Lennox Hearth
File size: 2.16 mb
File name:
Language of manual:en
Free link for this manual available at the bottom of the page



manual abstract


If used, remove the batteries from the battery holder. 3. This appliance is equipped with an ignition device which automatically lights the pilot. Do not try to light the pilot by hand. 4. Push the unit mounted "ON/OFF" switch to the "OFF" position. 6. Push the unit mounted "ON/OFF" switch back to the "ON" position. (The "ON/OFF" switch may include a wall switch if so equipped). Replace the batteries in the battery holder, if used. If the burner does not light or stay lit after several tries, turn the unit mounted "ON/OFF" switch to the "OFF" position and call your service technician or gas supplier. NOTE: Sufficient time must be allowed for air to escape from lines if the unit is being lit for the first time. 7. Turn HI-LO burner control knob to desired setting and close control door. PILOTOUTVENTLOTHTPTHTPHIININ 5. Allow sufficient length of time (minimum 5 minutes) for any gas in the combustion chamber to escape. If you still smell gas, STOP! Follow “B” in the safety information above on this page. If you do not smell gas, go to the next step. 8. Set thermostat to desired setting if applicable. 9. If the appliance will not operate, follow the instructions "To Turn Off Gas To Appliance" and call your service technician or gas supplier. TO SHUT OFF 1. Turn off all electrical power to the appliance (remote wall switch) or set the thermostat to the lowest setting, if applicable. Or remove batteries, if used. TO TURN OFF GAS TO APPLIANCE 1. For complete shut-down, turn remote wall switch to “OFF" 3. Turn off all electric power to the appliance and remove or set the thermostat to the lowest setting, if applicable. backup batteries if service is to be performed or for extended shutdown. 2. Turn the ON/OFF switch to “OFF”. If step 1 is not applicable. SUPERIORSUPERIORDIRECT-VENT GAS FIREPLACES • MODELS SLDVT-30/35/40/45 • CARE AND OPERATION INSTRUCTIONS REMARQUE : LES SCHEMAS ET LES ILLUSTRATIONS NE SONT PAS A L’ECHELLE SUPERIORSUPERIORDIRECT-VENT GAS FIREPLACES • MODELS SLDVT-30/35/40/45 • CARE AND OPERATION INSTRUCTIONS MAINTENANCE SCHEDULE Annually (Before the onset of the Burning Season) MAINTENANCE TASK ACCOMPLISHING PERSON PROCEDURE Inspecting/Cleaning Burner, Logs and Controls Qualified Service Technician Inspect valve and ensure it is properly operating. Check piping for leaks. Vacuum the control compartment, fireplace logs and burner area. Check Flame Patterns and Flame Height Qualified Service Technician Refer to Figures 12 through 14 on Page 16 and verify the flame pattern and height displayed by the appliance conforms to the picture. Flames must not impinge on the logs. Ensure flames are steady (not lifting or floating). Inspecting/Cleaning Pilot and Burner Qualified Service Technician Refer to Figure 16 (SIT Millivolt) or Figure 17 (Electronic) on Page 17. Remove any surface build-up on pilot and burner assembly. Wipe the pilot nozzles, igniter/flame rod and hood. Ensure the pilot flame engulfs the flame sensor as shown. Checking Vent Sys...

Other models in this manual:
Fireplaces - SLDVT-30NE (2.16 mb)
Fireplaces - SLDVT-30NE (2.16 mb)
Fireplaces - SLDVT-30NE (2.16 mb)
Fireplaces - SLDVT-30NE (2.16 mb)

Reviews



Your review
Your name:
Please, enter two numbers from picture:
capcha





Category