Votes - 3, Average rating: 5 ( )

Manafacture: Lennox Hearth File size: 1.55 mb File name: 62e3640e-c720-4259-8d9d-cfb899292f67.pdf Language of manual:

Remove the top louver assembly or radiant panel by pulling it out and off. 2. Open the control compartment access panel by actuating the spring-loaded magnetic catches securing the panel (gently depress the outer top corners of the louvered or radiant panel until the catches "pop" the door free, allowing it to swing out and down to the open position). 3. Locate the two (2) latches at the top of the control compartment. To disengage the two latches from the bottom vee-flange of the glass enclosure panel, reach for the handles located towards the back of the latches and pull the handles down toward the front of the appliance. 4. Swing the bottom of the door out and raise it slightly to lift the top flange of the door frame away from the appliance. Installing Glass Enclosure Panels (see Figure 6 ) 1. Visually inspect the gasket on the backside of the panels. The gasket surface must be clean, free of irregularities and seated fi rmly. 2. Position the glass enclosure panel in front of the firebox opening at a 45 degree angle and engage the top flange over the lip at the top of the fi rebox opening. See Figure 6. 3. Swing the glass enclosure panel down and back. Ensure the gasket seats evenly as the panel draws shut. Engage the Vee-flange at the bottom of the panel with the latches and close the latches to secure the panel. 4. Close the bottom control compartment access panel. Lower Compartment Door & Hinge Glass Door (Enclosure Panel) Top Flange Glass Door Figure 6 Firebox Floor Glass Door Latch Bottom Vee-fl ange Glass Door RE-INSTALLING GRATE, VERMICULITE, GLOWING EMBERS AND LOGS LOG SET - IDENTIFICATION LOG SET Catalog Number H3210 * Item Description A Log, Center B Log, Left Rear C Log, Left Front D Log, Right Rear E Log, Top Center F Log, Front Center * Item "letters" above correspond to photos on right REFERENCE Firebox Accessories / Parts Cat. No. Model No. Description 88L53 FGE Bag of Glowing Embers (1 oz. rockwool) 42363 Vermiculite, Bag (2 liters) WARNING The size and position of the log set was engineered to give the appliance a safe, reliable and attractive flame pattern. Any attempt to use a different log set in the fireplace will void the warranty and will result in incomplete combustion, sooting, and poor fl ame quality. Glowing Embers Separate into Quarter Size (separate) Pieces Bag of Glowing Embers (rockwool) Figure 7 Bottom View of Logs (in packaging) F D Top View of Logs C E A B Top View of Logs - Installed E B C F A D F E A C B D (Valve Access Side) Position The Groove At The Bottom Of Log (A) Over The Grate And Slide It Forward Against The Grate Here Figure 9 READ LOG WARNINGS ON PAGE 9 BEFORE PROCEEDING 1. Remove front glass enclosure panel from appliance. a. Open Control Compartment Access Panel (see Control Compart- ment Access Instructions on Page 4. b. Remove the glass panel enclosure (see Removing Glass Enclosure Panel instructions on Page 9. 2. Remove the following from firebox; log set, embers (rockwool) and vermiculite. Handle logs carefully to prevent breakage. 3. Ensure the Grate is properly installed in the firebox with the 4 legs of the grate fi tting into the 4 dimples on the fi rebox fl oor. 4. Install Vermiculite-Place some vermiculite on the firebox floor around the grate (the entire bag of vermiculite will NOT be used). See Figure 15 on Page 13. DO NOT PLACE ANY VERMICULITE ON THE BURNER. 6. Placement of Glowing Embers - Separate the Embers (rockwool) into pieces about the size of a quarter (see Figure 7 ). Keep the pieces fluffed up, not matted. Distribute these pieces over the surface of the burner, as shown in Figure 8. Do not use more than is necessary. Ensure that the main burner ports remain uncovered by the ember material. Note: This appliance is provided with enough Glowing Embers for several applications, do not use all that is in a new bag at one time. For best glowing effect, replace the ember material annually. Replacement Glowing Embers are available (order Catalog Number 88L53). B C D A (Valve Access Side) (Valve Access Side) (Valve Access Side) (Valve Access Side) Position Groove At The Bottom Of Log (A) Over The Log Support Here 8. Place Log (B) as shown in Figure 10. Position Log (B) Against The Back Of The Grate Here Position Groove at The Bottom Of Log (B) Over The Grate Here And Slide It Against The Back Of The Grate Figure 10 Log (C) Lays Over Logs (A) and (B) A B Position And Slide Log (D) Against The Back Of The Grate Place Log (D) Over TheFlat Spot On Log (A) Here A Position The Groove in The Back of Log (C) Against The GrateFigure 11 9. Place Log (C) as shown in Figure 11. Figure 12 10. Place Log (D) as shown in Figure 12. Figure 8 Place Embers on burner as shown. DO NOT PLACE EMBERS OVER GAS PORTS / AREAS CIRCLED 7. Place Log (A) on the grate as shown in Figure 9 10. 10. Position round end of log (E) against the notch of log (D) here. Two charred spots face the front Figure 13 D E C Position Small End of Log (E) on The Notch of Log (C) Here (Valve...

Download now

Please, enter two numbers from picture: