Votes - , Average rating:
(
)
)
Manafacture: Vermont Casting
File size: 14.5 mb
File name: e6d09e9c-1499-4124-bdcd-1696cb58faf6.pdf
Language of manual:
The document is loading, please wait
 |
The document is loading, please wait
manual abstract
After the initial cleaning process the glass should be cleaned two or three times during each operating season depending on the environment in the house. Clean the glass after the first two weeks of operation. • The use of any non-approved replacement glass will void all product warranties. • Care must be taken to avoid breakage of the glass. • Do not operate appliance with glass front removed, cracked or broken. • A replacement glass frame assembly (complete with gasket) is available through your CFM Corporation dealer and should only be installed by a licensed qualified service person. Operating Instructions Glass Information Glass Frame Assembly Removal Glass Cleaning Ceramic Refractory Installation The ceramic refractories are fragile and should be handled with care. Due to the size of the refractories, an assistant may be helpful. .. .............. ............................ ........................ .................................... .......................... ........................................ .............................. ............ .............................. ........ FP1800 Phillips Screws Fig. 39 Remove Phillips screws, tilt frame forward and lift off bottom door track. FP1580a DVT38s2 refractory 6/05 Refractory, Left Side Refractory, Right Side FP1580a Fig. 40 Ceramic refractory panels. 1. Using a Robertson screwdriver, remove the two (2) nuts holding each fettle to the burner assembly. 2. Identify the side refractory. The refractory with the small cut out at the bottom must be installed on the side where the plumbing for the pilot and manifold are. The other side refractory has a larger cut out at the bottom. This is designed to allow the opening for the fresh air coming to the combustion chamber unobstructed. (Fig. 40) 3. Start with either the right side refractory or left side refractory. Hold the refractory at an angle. Slide and seat the bottom edge toward the bottom of the Chateau™ Direct Vent Gas Fireplace firebox. Tilt it carefully toward the side until the piece is in place. Using the two (2) brackets and four (4) screws provided with the refractory kit, fasten each bracket to the top of the firebox on each side. NOTE: Use existing holes in firebox. 4. Place the right and left hearth refractories at on each side of the burner tube assembly. 5. Install the end hearth refractories and align with the right and left hearth refractories already installed. 6. Reinstall the burner tube and fettle. Log, Lava Rock and Ember Placement Unpack the logs from packaging and remove each log from its wrapping material. The logs are fragile and should be handled with care. Keep the packaging materials out of the reach of children and dispose of the material in a safe manner. IMPORTANT: Review these instructions and familiarize yourself with each log before beginning log placement. Find the notches, pins and indentations on each log. Follow the instructions closely, using the Log ID (Fig. 41) and the illustrations to assist in correctly placing each log. Log Pilot Plumbing (F50) Log Overlay (F56) Log Grate/Burner Tube (F51) (2) Log Right Grate (F49) (2) Log Front Upper Right (F47) (2) Log Middle (F52) Log Left Grate (F53) (2) Log Front Right (F48) LG492 Fig. 41 DVT38Sw log identification. LG492 Log id 6/07 28 20011957 29 Chateau™ Direct Vent Gas Fireplace 20011957 1. Ensure the four (4) screws that attach the fettle to the burner are secure. 2. Set the andirons in place by hooking the tabs on the back of the andirons over the webs of the fettle. (Fig. 42) Repeat process for andirons on both sides of burner. ............ ........................ ........ Andirons Burner Housing Burner Tubes Fettle FP1803 Figure 42 3. Place the volcanic rock in front of each burner tube assembly and around the burner assembly as desired. (Fig. 43) Do not obstruct fresh air inlet with volcanic rock. 4. Place the ember material lightly, between each burner tube assembly and the burner housing, between the joined burner tubes and in front over the burner tube and on top of burner tube. NOTE: The ember material must be built up from the burner tubes to the burner housing fronts in order for the burner tubes to light properly. .......... ...................................... ........ Figure 43 LG486 Ember Material Lava Rock 5. Position the log pilot plumbing. (Fig. 44) Hold the log with the two (2) branches facing down and set it down over the pilot plumbing with the flat side of the log touching the side refractory. .......... Log Pilot Plumbing (F50) LG493 Figure 44 Chateau™ Direct Vent Gas Fireplace 6. Position the log burner overlay. (Fig. 45) The overlay is very fragile and must be handled with extra care. Hold the overlay with the flat surface facing down. The notched corners of the overlay should be on the side of the pilot. Set the overlay on top of the burner housing and align it right to left over the burner housing. Make sure the overlay fits between the two (2) fettles. 7. Position the log grate/burne...