Votes - 4, Average rating: 4.3
(
)
)
|
manual abstract
Construction and electrical outlet wiring must comply with local building codes and other applicable regulations to reduce the risk of fire, electric shock and injury to persons. Do not attempt to wire your own new outlets or circuits. To reduce the risk of fire, electric shock or injury to persons, always use a licensed electrician. FIREPLACE INSTALLATION 1. Make sure the units switched OFF (refer to section). 2. Plug the unit into a 15Amp/120VAC outlet. If the cord does not reach, you may extension cord rated for a minimum watts. 60323.75 8.90 26.18 OPERATION - see Fig. 2 Three switches provide a choice of heat settings. A switch is in the ON position when the side with the markings on (i.e. I, I, or II) is pushed in. Switch 1 (I) Controls the electricity supply to the heater and flame effect. Note: This switch must be in the ON (I) position for heater to operate with or without heat. Switch 2 (I) Provides 600 W heat output. Switch 3 (II) Provides 1200 W heat output with switch 2. 1 2 3 IIIIIFIG. 2 RESETTING THE CUTOFF SWITCH Should the heater overheat, turn the heater off and it without being reset. It can be reset by switching MAIN ON/OFF SWITCH to OFF minutes before switching the unit CAUTION If you need to continuously reset the heater, unplug the unit and call customer service at 1-800-668-6663. MAINTENANCE WARNING: Always disconnect from the power supply before attempting any maintenance. Bulb Replacement - see Fig.’ s 3, 4 & 5 There are two bulbs located under the ember bed. To gain access to the bulbs, remove the coal/ pebbles and place in a container. Remove the front panel from the fireplace by lifting it up and out from the slots on the fireplace - see Fig.3. Remove the rotisserie by carefully sliding the rubber connecter off the motor shaft - see Fig. 4. Remove the defective bulb by unscrewing it as shown in Fig.5. Replace with a 60W E12 clear chandelier or candelabra bulb. Take care not to over-tighten the bulb.Refit the front panel and replace the coal/ pebbles. FIG. 3 FIG. 4 FIG. 5 8 HELPFUL HINTS It is a good idea if they are close to Group replacement will reduce need to open the unit to CLEANING WARNING – Always disconnect from the power supply before cleaning the fireplace. For general cleaning use a soft clean use abrasive cleaners. The glass viewing should be cleaned carefully with a soft cloth. NOT use glass cleaners. To remove any accumulation of dust or fluff the soft brush attachment of a vacuum cleaner should occasionally be used to clean the outlet grille of the heater assembly. ONE YEAR LIMITED Products to which This limited warranty applies newly purchased Dimplex fireplaces and surrounds (This limited warranty applies only to purchases Canada except for Yukon Territory, Nunavut, or Northwest Territories or in any of the 50 States of the USA (and the District of Columbia) except for Hawaii and Alaska. This limited warranty applies to the original purchaser product only and is not transferable. Products excluded from this limited warranty Light bulbs are not covered by this limited warranty and the sole responsibility of the owner/purchaser. Products purchased in Yukon Territory, Nunavut, Northwest Territories, Hawaii, or Alaska are not covered by this limited warranty. Products purchased in these States, provinces, or territories are sold AS IS without warranty or condition of any kind (including, without limitation, any implied warranties or conditions of merchantability or fitness for a particular purpose) and the entire risk of as to the quality and performance of the products is with the purchaser, and in the event of a defect the purchaser assumes the entire cost of all necessary servicing or repair. What this limited warranty covers and for how long Products covered by this limited warranty have been tested and inspected prior to shipment and, subject to the provisions of this warranty, Dimplex warrants such products to be free from defects in material and workmanship for a period of 12 months from the date of the first purchase of such product. The limited 12 month warranty period also applies to any implied warranties that may exist under applicable law. Some jurisdictions do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to the purchaser. What this limited This limited warranty been repaired (except representatives) or otherwise does further not apply to defects abuse, accident, neglect, incorrect maintenance or handling, or operation source. What you must do to get service under this Defects must be brought to the attention of Dimplex Technical Service by contacting Dimplex at 1-888- DIMPLEX (1-888-3467539), or 1367 Industrial Road, Cambridge Ontario, N1R 7G8. Please have proof of purchase, catalogue/model and serial numbers available when calling. Limited warranty service requires a proof of purchase of the product. What Dimplex will do in the event of a defect In the event a product or part covered by this limited...