Votes - 2, Average rating: 4
(
)
)
|
manual abstract
Il est recommande d’installer une barriere physiquesi des personnes a risques habitent la maison. Pour empecher l’acces a un foyer ou a un poele, installez une barriere de securite; cette mesureempechera les tout petits, les jeunes enfants et toute autre personne arisque d’avoir acces a la piece et aux surfaces chaudes. OPERATION AND CARE OF YOUR APPLIANCE Gas Valve Piezo Igniter Latch for Glass Door HI/LO (flame height control knob) OFF/PILOT/ON (gas control knob) Gas Flex-line Optional ON/OFF Switch Can be Installed Here Glass Door is Above Control Compartment Control Compartment Access Figure 1 Gas Shut-Off Figure 2 OPENING CONTROL COMPARTMENT DOOR Control Valve Lower Control Compartment Door Lift the Lower Control Compartment Doorup and pull out to remove. Up Out Hook Catch GAS CONTROLS/CONTROL COMPARTMENT ACCESS Thegascontrolscanbefoundbehindthecontrol compartment access door. NOTE: The top louvered panel and the bottom louveredcontrolcompartmentdoorwillremove and install the same way as follows: Removing Control Compartment Door: Open the door by gently lifting it upward until thehookcatchesonbothsidesclearthelocating slots. Then pull door out to remove. On millivolt systems, the piezo igniter, HI/LO flame adjustment knob, and pilot and main gas OFF/PILOT/ON control knob are located below the glass panel enclosure. See Figures 1 through 3. Reinstalling Control Compartment Door: To reinstall, insert the hook catches on each side of the door into the corresponding slots in the control compartment opening, then gently push forward and slide down until it locks in place. The standard controls for appliance operation are located behind the lower louvered control compartment door located below the appliance front glass enclosure panel (see Figures 1 and 2). Optional control switches are also available (see Page 16 -Rocker Switch, Remote Wall Switch, Remote Control, Unit Mounted Rocker Switch or Wall Thermostat). Before lighting and operating your appliance familiarize yourself with the gas control valve that your appliance uses. Refer to Figures 1 through 3. To light millivolt appliances refer to the detailed lighting instructions found on Page 19 .Millivolt appliance lighting instructions may also be foundonthepulloutlightinginstructionlabels attached to the gas control valve. Once the pilot is lit, the main burner may be turned ON and OFF using a wall switch, remote control, optional on unit rocker switch (FRS), or wall thermostat. To operate: Toggle the switch between its ON and OFF positions. If your millivolt appliance is equipped with an optional remote switch kit (wall switch, remote control, rocker switch, or wall thermostat) and the pilot is lit, the appliance main burner may be turned on and off using the optional switch. Note: Topreventexcessive resistanceinburner circuit (which can cause burner operation problems), only one burner control switch should be wired to valve. NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. SIT Millivolt Gas Valve Inlet Pressure Tap SIT Millivolt Gas Valve Inlet Pressure Tap Adjustment Manifold Pressure Tap Main Gas HILOWHTPTHTPTPILOTPILOTONitOFFINOUT Pilot Adjustment Control Knob Screw OFF/PILOT/ON Figure 3 Variable Flame Height Adjustment (Millivolt Appliances) All Millivolt appliances are equipped with a variable gas control valve. Flame height for t...
Other models in this manual:Fireplaces - SDV SDVPF-N-B (2.24 mb)
Fireplaces - SDV SDVPF-N-B (2.24 mb)
Fireplaces - SDV SDVST-N-B (2.24 mb)
Fireplaces - SDV SDVST-N-B (2.24 mb)