Votes - 2, Average rating: 4
(
)
)
|
manual abstract
Please retain this manual for reference Distributed by: RTA International Youngtown, AZ 85363 1-888-775-1330 OWNER’S MANUAL Read These Safety Instructions......................................... Contents Breakdown.......................................................... Screw Packing List............................................................. Assembly Procedure.......................................................... Assembly.......................................................................... Safety First........................................................................ Tabletop Heater Location.................................................... Checking For Leaks............................................................ Before Operating................................................................ Operating.......................................................................... After Operating.................................................................. Maintenance...................................................................... Storage............................................................................. Troubleshooting................................................................. TABLE OF CONTENTS 1 2 3 3 4 7 8 8 8 9 11 11 11 12 All rights reserved No part of this manual may be reproduced transmitted stored in a retrieval system or translated into any language in any form by any means mechanical optical electronic recording or otherwise without the written permission of Changzhou Gardensun Furnace Co Ltd . , , , , , , , , ., . ., . , . , .,. Changzhou Gardensun Furnace Co Ltd Reserves the right to revise this manual and to make changes to any or all parts at any time without obligation to notify any person or entify of such revision and changes Copyright © 2006 Changzhou Gardensun Furnace Co Ltd 2006 Edition the front page OWNER’S MANUAL If you smell gas Shut off gas to the appliance Extinguish any open flame Open lid If odor continues immediately call your Gas supplier or your life Department : . . . , . Only to be used outdoors Warning Accessible parts may be very hot Keep young children away Turn off the gas supply at the gas container after use Any modification of the appliance may be dangerous . : . . . . Failure to comply with these instructions could result in a fire or explosion that could cause serious bodily injury death or property damage , , . Gas leaks may cause a fire or explosion can cause serious bodily injury or death or damage to property You must follow all leak checking procedures operating this unit Never use an open flame to check for leaks , . . . Do not store or use gasoline or other flammable vapors or liquids in the vicinity of this or any other appliance Danger Carbon monoxide hazard 1 This appliance can produce carbon monoxide which has no odor 2 Using it in an enclosed space can kill you 3 Never use this appliance in an enclosed space as camper tent car or home Do NOT touch or move heater for at least 45 minutes after use Dome is hot to the touch Allow dome to cool before touching . . . . . . ,, . . . . READ THESE SAFETY INSTRUCTIONS WARNING ATTENTION FOR YOUR SAFETY WARNING 1 OWNER’S MANUAL 2 CONTENTS BREAKDOWN OWNER’S MANUAL 3 Item No. Item Qty. Item No. Item Qty. 1 M6 Castle nut 3 11 Burner 1 2 Reflector 1 12 3/16" bolt 4 3 O6mm Washer 3 13 M5.10mm bolt 1 4 Emitter screen 1 14 Tank Housing 1 5 Guard 1 15 Igniter button 1 6 Door Plate 1 16 Control knob 1 7 Base 1 17 Handle 1 8 Cast Iron 1 18 Regulator 1 9 M6.15mm bolt 4 19 60mm pin 3 10 3/16" bolt 4 20 M6 flange nut 3 SCREW PACKAGING LIST Item Qty. Item Qty. M6 Castle nut 3 M5.10mm bolt & M5 nut 1 O6mmWasher 6 60mm pin 3 M6.15mm bolt 4 M6 flange nut 3 3/16" bolt 8 Wrench 1 Tools needed: ( not included) Adjustable opening wrench (2) 20 cm long Slip joint pliers 23 cm long Philips screwdriver w/medium blade Teflon plumbing tape for joints ASSEMBLY PROCEDURE OWNER’S MANUAL 4 ASSEMBLY 1-1. Take out all the parts of the tabletop Heater. 1-2. Aim the cast iron at the holes on the base. 2-1. Use 4pcs M6X15mm bolts to fix the tank housing to the base & cast iron. 2-2. Tighten the bolts as above show. 3-1. Put the burner on the tank housing then fix them with 4pcs 3/16” bolts. 4-1. Fix the regulator to the t a n k h o u s i n g w i t h t h e M5X10mm bolt & M5 nut. STEP 3 STEP 4 STEP 1 STEP 2 OWNER’S MANUAL 5 5-1. Fix 3pcs pins of 60mm length to the emitter screen with 3pcs M6 flange nuts then tighten them. 6-1. Put the emitter screen on the burner. 6-2. Use 4pcs 3/16” bolts to connect the emitter screen to the burner. Tighten the bolts. 7-1. Put the guard on the burner through the emitter screen. 7-2. Put the ends of the guard into the holes of the burner. 8-1. Put 3pcs washers on each pins of the 60mm length. STEP 5 STEP 6 STEP 7 STEP 8 OWNER’S MANUAL 6 10-1. Fasten the reflector with 9-1. Put the reflector through 3pcs M6 Castle nuts. the pins and on th...