Votes - 5, Average rating: 3.8 ( )

Manafacture: Sunbeam File size: 641.63 kb File name: Language of manual:

Arrange 16. Avoid the use of an extension cord because the This heater is equipped with a patented, technologically- cord away from traffic area and where it will not be extension cord may overheat and cause a risk of I/O - Off Mode advanced, ceramic controlled safety system that requires tripped over. fire. However, if you have to use an extension cord, If you want to shut off the heater at any time of A the user to reset the heater if there is a potential If you have any questions regarding your product or overheat situation. When a potential overheat 5. This heater is not intended for use in bathrooms, the cord shall be No. 14 AWG minimum size and operation, turn the Mode Control to Off ( I/O ) position. would like to learn more about other Sunbeam® temperature is reached, the system will automatically laundry areas and similar indoor location. NEVER rated not less than 1875 watts. Power Light may remain lit until the heater is unplugged. A. MODE CONTROL (OFF, FAN, LOW, HIGH) products, please contact our Consumer Service locate heater where it may fall into a bathtub or 17. If the heater will not operate, see specific instructions shut the heater off. It can only resume operation when Department at 1-888-264-9669 or visit our website at -Fan only Setting B. THERMOSTAT CONTROL other water container. on Auto Safety Shut-off. the user resets the unit. 6. Extreme caution is necessary when any heater is 18. DO NOT attempt to repair or adjust any electrical or Heater will run at fan-only operation without heat output. used by, or near children or invalids, and whenever mechanical functions on this unit. Doing so will void To Reset the Heater: 1 - LOW Heat the heater is left operating and unattended. your warranty. The inside of the unit contains no user If the unit shuts down: 7. Always unplug the heater when not in use. serviceable parts. All servicing should be performed The heater will run continuously at 1000W. 1. Turn Mode Control to OFF ( I/O ) and Thermostat Figure 2 8. When unplugging, be sure to pull by the plug and by qualified personnel only. 2 - HIGH Heat BA Control fully clockwise to HIGH ( Largest ). not the cord. 19. Discontinue use if plug or outlet is hot. It is 2. Unplug unit, wait 30 minutes. The heater will run continuously at 1500W. 9. DO NOT insert or allow foreign objects to enter any recommended that the outlet be replaced if plug or D 3. Plug in and turn ON. NOTE: To start the heater operation, make sure the ventilation or exhaust opening as this may cause an outlet is hot to touch. Thermostat Control is turned fully clockwise to the highest electric shock or fire, or damage the heater. C position ( Largest ). 10. DO NOT operate heater with a damaged cord or PLEASE READ AND SAVE plug, or after the heater malfunctions, has been Thermostat Control dropped or damaged in any manner. Return THESE IMPORTANT SAFETY 1. Before setting the thermostat, allow heater to appliance to manufacturer for examination, electrical operate and warm up the room. As noted above, you or mechanical adjustment, or repair. INSTRUCTIONS need to set thermostat on HIGH ( Largest ) to A. REAR CARRY HANDLE start the heater. B. THERMOSTAT CONTROL THIS APPLIANCE HAS A POLARIZED PLUG (one blade is wider than the2. When the desired temperature comfort level is C. POWER LIGHT other). To reduce the risk of electric shock, this plug is intended to fit inreached, lower the thermostat setting until the a polarized outlet only one way. If the plug does not fit fully in thefan/heater stops operating. This is done by moving D. MODE CONTROL outlet, reverse the plug. If it still does not fit, contact a qualifiedthe Thermostat Control anti-clockwise toward the LOW electrician to install the proper outlet. ( Smallest ) setting. DO NOT ATTEMPT TO MODIFY THIS PLUG OR DEFEAT THIS SAFETY FEATURE IN ANY WAY. ...

Download now

Please, enter two numbers from picture: