Votes - 1, Average rating: 5 ( )

Manafacture: Gas-Fired Products File size: 974.39 kb File name: Language of manual:

1). The burner will light. DO NOT operate the heater in any other than the full “ON” position. 9. IMPORTANT: DO NOT attempt to adjust the main burner input using the main gas supply valve, for this may cause the pilot and thermocouple to shut down the burner (Fig. 2). Shut-down instructions: To turn the heater OFF, • For short periods of time, turn the main burner off by rotating the gas valve knob clockwise to the “PILOT” position. • For extended periods of non use, turn the appliance completely off by rotating the gas valve knob clockwise to the “PILOT” position, depress the knob slightly, then rotate the knob fully clockwise to the “OFF” position. (Note: For Model 120L, also turn off the gas supply cylinder.) Pilot burner adjustment: 1. Remove the pilot adjustment cap. The pilot adjustment cap is a slotted screw located in front of the “Pilot” designation stamped on top of valve body just below the gas valve knob. 2. Adjust the pilot key to provide properly sized flame. Rotate the key “clockwise” to decrease or “counterclockwise” to increase flame. 3. Replace the pilot adjustment cap. MAINTENANCE INSTRUCTIONS This heater (including hose and regulator assembly if applicable) must be inspected before each use. If the hose for the Model 120L shows evidence of excessive abrasion or wear, or if the hose is cut, it must be replaced prior to the heater being put into operation. The replacement hose assembly shall be that specified by the manufacturer. See the parts list. The appliance area must be kept free and clear of combustible materials, gasoline and other flammable vapors and liquids at all times. The flow of combustion and ventilation air must not be obstructed. Cleaning the heater: Periodically, the heater must be cleaned of all dirt and dust particles. DANGER DO NOT ATTEMPT TO CLEAN THE HEATER WHILE IT IS OPERATING OR WHILE IT IS STILL HOT. Turn the heater off and wait until it has completely cooled (at least 20minutes) before cleaning. Clean the outside of the heater using a damp cloth. DO NOT clean the heater by spraying water on it. Wipe the outside of the heater off with a dry cloth after cleaning. Clean the inside of the heater using compressed air. Blow air back and forth along all inside surfaces until all dust has been dislodged. Clean the orifice of each burner with a #69 drill bit (for LP-Gas). Clean the orifice manually (by hand) – DO NOT use power drill. Clean the thermocouple lead. DO NOT operate this heater if any part has been under water. Call a qualified service person to inspect the appliance and to replace any part of the control system or gas control valve which has been under water. This heater must be inspected at least annually by a qualified service person. WARNING Do not exceed . PSI gas pressure to appliance gas control valve. Enerco Group, Inc. | Gas-Fired Infra-Red Portable Construction Heater 5 Operating Instructions and Owner’s Manual REPLACEMENT PARTS LIST FOR MODELS HS125NG / MH125LP / HS125LP SEE BACK PAGE FOR PARTS ORDERING INFORMATION Figure 1 Figure 2 REF. # ITEM # DESCRIPTION 1 ...................... 00332 ............ Manual Control Valve 2 ...................... 04466 ........... Filter/Diffuser 3 ...................... 05363 ............ Orifice Pilot(MH125LP/HS125LP) 4 ...................... 09352 ............ Thermocouple 5 ...................... 11357 ............. Pilot Burner 6 ...................... 11663 ............ Regulator (MH125LP/HS125LP) 7 ...................... 11666 ............ Regulator (HS125NG) 8 ...................... 05374 ............ Orifice Pilot (HS125NG) 9 ...................... CR805 ........... Ignitor 10 ..................... CR835 ........... Piezo 11 ..................... CR820 ........... Axle 12 ..................... CR815 ............ Axle Brackets 13 ..................... CR725 ........... Handle 14 ..................... CR810 ........... Wheel 15 ..................... M9005 .......... Valve Supply Tube 16 ..................... M9010........... Valve Supply Tube Clamp 17 ..................... M9015 ........... Burner Manifold 18 ..................... M9020 .......... Burner Enerco Group, Inc. | Gas-Fired Infra-Red Portable Construction Heater 6 Operating Instructions and Owner’s Manual GAS-FIRED INFRA-RED PORTABLE CONSTRUCTION HEATER MODELS HS125NG / MH125LP / HS125LP 4 3 2 1 5 6 7 8 9 10 1112 13 14 Combustion Chamber Mounting Bracket Pilot Supply Tube Propane Hose Top Plate 15 16 17 18 Frame Assembly Enerco Group, Inc. | Gas-Fired Infra-Red Portable Construction Heater 7 Operating Instructions and Owner’s Manual OPERATING INSTRUCTIONS AND OWNER’S MANUAL MR. HEATER READ INSTRUCTIONS CAREFULLY: Read and follow all instructions. Place instructions in a safe place for future reference. Do not allow anyone who has not read these instructions to assemble, light, adjust or operate the heater. HEATSTAR MH125LP MODELMODELHS125NG, HS125LP WARNING: USE ONLY MANUFACTURER’S REPLACEMENT PARTS. USE OF ANY OTHER PARTS COULD CAUSE INJURY OR DE...

Download now

Please, enter two numbers from picture: