Votes - , Average rating: ( )

User manual CFM Corporation, model RMC-TT15

Manafacture: CFM Corporation
File size: 531.89 kb
File name:

Language of manual:

The document is loading, please wait

Download nowClose

The document is loading, please wait

Download nowClose

Do not use inside house, camper, tent, vehicle or any type of unvented or enclosed area. 5. Never operate heater while sleeping or unattended. Keep children and animals away from heater. 6. This heater produces carbon monoxide, which is listed by the State of California as a reproductive toxin under Proposition 65. 7. Minimum heater clearances from combustibles: Top and Front 5 ft. Sides and Rear 3 ft. 8. Use only in well vented areas. 9. Use only propane gas set up for vapor withdrawal. 10. Before connecting heater to propane tank, make sure heater regulator knob is in the “OFF” position. Always connect and light heater in areas free of open flames. 11. Before each use, check heater for leaks. Never use an open flame to check for a leak. Apply a mixture of liquid soap and water to all joints. Bubbles forming show a leak. Correct all leaks at once. 12. Locate propane tank on a stable and level surface. The heater burners must be at least two feet above the floor. Always attach heater to propane tank in an upright position. Never operate heater on its side or attach to propane tank in a horizontal position. This could lead to dangerous flare-ups or fire. 13. Do not use heater in basement or below ground level. Propane is heavier than air. If a leak occurs, propane gas will sink to the lowest possible level. If you smell gas or suspect a leak, shut off the propane tank valve at once and ventilate the area. Do not strike a match or create any flame or electric spark. Find and correct leak before attempting to light any appliance. If you cannot correct leak, do not tamper with heater. Return heater to nearest authorized service center or to address on back page of this manual, freight prepaid. 14. Do not remove or handle a hot or operating heater. Do not attach or remove a propane tank from a hot or operating heater. Severe burns may result. 15. Always remove heater from propane tank after each use. Always store propane tank outdoors. Never store propane tank in an enclosed area. Never store propane tank near high heat, open flame or where temperatures exceed 100°F. 16. Keep all connections and fittings clean. Make sure propane tank valve outlet is clean. Check the “O: ring on the heater inlet fuel connector for damage before each use. Replace if worn or damaged. 17. Do not attempt to light one burner off of the other. Use one match per burner. 18. Do not overlap or point burners at each other. 19. Do not raise burner heads and cover air inlet holes in mixing tube with burner head bracket. 20. Wing nuts and burner heads become very hot during operation. Do not attempt to adjust burner position while heater is operating. Allow 15 minutes to cool. 21. Check heater for damage before each use. Do not use a damaged heater. Do not alter heater. Keep heater in its original state. Do not use heater if altered. 22. If possible, keep containers in a warm area (under no circumstances should the heater exhaust be directed toward the propane container). 3 Heater Assembly (Dual burner models only) The tank collar bracket must be assembled before the heaters can be attached to the propane tank. 1. Align bolt holes in tank collar bracket and piezo bracket with bolt holes in center plate on manifold. 2. Thread two machine screws into the bolt holes attaching tank collar bracket and piezo bracket to center plate on manifold. (Fig. 1) 3. Connect spark plug cable (left) and spark plug cable (right) into each terminal of piezo lighter. A CAUTION: The spark plug cables have different connectors. Be sure to connect each spark plug into the correct terminal. Make sure terminals are securely connected. Fig. 1 Assemble tank collar bracket. Connecting Heater to Propane Tank Read and understand all safety information before connecting heater to propane tank. 1. (Applies to dual burner models only). Place heater onto tank with tank collar bracket over tank collar (Fig. 1) Mounting bolt knob should be positioned to the outside of tank collar. 2. (Applies to dual burner models only). Firmly secure to tank by hand-tightening mounting bolt knob. Do not overtighten mounting bolt knob. 3. Make sure heater regulator knob is in the “OFF” position. 4. Wrench tighten the fuel connector nut into the propane tank valve with both gas hose fittings in a horizontal position. (Fig. 1) Turn fuel connector nut counterclockwise to tighten. Threads are lefthanded. 4 Fig. 2 Attach heater to tank with tank collar bracket. 5. Connect the hose to inlet connector. (Fig. 2) Tighten firmly using wrench. Make sure hose is connected before opening the tank valve. 6. Open propane tank valve slowly. 7. Check all fittings for leaks. Apply a mixture of liquid soap and water to all joints. Bubbles forming show a leak. Correct all leaks at once. A WARNING: Never use an open flame to check for leaks. 8. Always remove propane tank from heater after each use. Do not store heater while attached to propane tank. Operation A WARNING: B...