Votes - 5, Average rating: 3.4
(
)
)
|
manual abstract
120° Approvals ..................... UL/CUL listed. Close mesh blower guard meets OSHA requirements. OSCILLATING CERAMIC HEATER with REMOTE CONTROL MODEL 3LY41/8540 OPERATING INSTRUCTIONS GENERAL SAFETY INFORMATION 1. Use this Heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electrical shock, or injury to persons. 2. This Heater is intended for GENERAL USE ONLY. 3. Make certain that the power source conforms to the elec- trical requirements of the Heater. 4. Extreme caution is necessary when any Heater is used by or near children or invalids and whenever the Heater is left operating unattended. 5. The power cord is equipped with a three-prong grounded plug that must be inserted into a matching receptacle. Un- der no circumstances must the grounding prong be cut off the plug. Where a two-prong wall receptacle is en- countered, it must be replaced with a properly grounded three-prong receptacle, installed in accordance with the Na- tional Electrical Code (NEC) and all applicable local codes and ordinances. This work must be done only by a quali- fied electrician, using copper wire only. WARNING: USE OF A THREE-PRONG TO TWO-PRONG ADAPTER IS NOT RECOMMENDED. IMPROPER CONNEC- TION MAY CREATE THE RISK OF ELECTROCUTION. USE OF SUCH ADAPTERS ARE NOT PERMITTED IN CANADA. 6. Where possible, avoid the use of extension cords because the extension cord may overheat and cause a risk of fire. If they must be used, minimize the risk of overheating by en- suring that they are CUL/UL listed, a minimum No. 14 AWG, rated not less than 1875 watts and of proper length. Never use a single extension cord to operate more than one Heater. 7. Do not operate any Heater with a damaged cord or plug or after the Heater malfunctions, has been dropped or damaged in any manner. Return Heater to authorized service facility for examination, electrical or mechanical adjustment or repair. 8. Unplug power cord before servicing or moving the Heater. Always unplug Heater when not in use. WARNING: DO NOT DEPEND ON THE ON/OFF SWITCH AS THE SOLE MEANS OF DISCONNECTING POWER WHEN SERVICING OR MOVING THE HEATER. ALWAYS UNPLUG THE POWER CORD. 9. Do not insert or allow fingers or foreign objects to enter any ventilation or exhaust opening as it may cause an electric shock or fire, or damage the Heater. Do not block or tamper with the Heater in any manner while it is in operation. 10. To prevent a possible fire, do not block air intakes or ex- haust in any manner. Do not place on soft surfaces, like a bed, where openings may become blocked. 11. Always place the Heater on a stable, flat, level surface when op- erating, to avoid the chance of the Heater overturning. Locate the Power Cord so the Heater or other objects are not resting on it. Do not run Power Cord under carpeting. Do not cover Power Cord with throw rugs, runners, or the like. Arrange Power Cord away from room traffic and where it will not be tripped over. 12. This Heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. Always use handle when moving this Heater. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes and curtains at least 3 feet (0.9 m) from the front of the Heater and keep them at least 1 foot (0.3 m) from the sides and rear. 13. A Heater has hot and arcing or sparking parts inside. It must NOT be used in potentially dangerous locations such as flammable, explosive, chemical-laden or wet atmo- spheres. Heater is intended for general use ONLY. 14.This Heater is not intended for use in wet or damp locations. Never locate a Heater where it may fall into a bathtub or other water container. 15. Do not use Heater outdoors. WARNING: REDUCE THE RISK OF FIRE OF ELECTRIC SHOCK – DO NOT USE THIS HEATER WITH ANY SOLID STATE SPEED CONTROL DEVICES. MODEL 3LY41/8540 OPERATION Control Panel: (Figure 1) 1. When the heater is plugged in there will be a “beep” to indicate that there is power to the unit. 2. ON/FUNCTION button. When this button is pushed, HIGH indicator light comes on and heater is in the high heat mode. (1500 watts) 3. Press the ON/FUNCTION button again the HIGH indicator light goes off and the LOW indicator light comes on and the heater is now in the low heat mode. (900 watts) 4. Press the ON/FUNCTION button again and the LOW indicator light goes off and the FAN indicator light comes on and the heater is in fan only mode. 5. OFF button – Press this button will shut the heater off. 6. “TIMER” button. Press it once and the light comes on indicating 1/2 hour of time. Press it again and the light indicates 1 hour. Press it a third time and it indi- cates 1.5 hours. The total time that can be indicated at one time is 7.5 hours. Continuing to press the timer button will cycle through the settings until all timer lights are off. When the time indicator lights are off, the heater will run continuously. 7. The “SWING” button. Press this button and the swing light comes on and ...
Other models in this manual:Electric Heaters - 3LY41/8540 (150.7 kb)