Votes - 2, Average rating: 4
(
)
)
|
manual abstract
These currents move heat to wall surfaces next to heater. Installing heater next to vinyl or cloth wall coverings or operating heater where impurities (such as, but not limited to, tobacco smoke, aromatic candles, cleaning fluids, oil or kerosene lamps, etc.) in the air exist, may discolor walls or cause odors. IMPORTANT:Vent-free heaters add moisture to the air. Although this is beneficial, installing heater in rooms without enough ventilation air may cause mildew to form from too much moisture. See Air for Combustion and Ventilation, pages 4 through 6. CHECK GAS TYPE Use only natural gas. If your gas supply is not natural gas, do not install heater. Call dealer where you bought heater for proper type heater. CLEARANCES TO COMBUSTIBLES (Vent-Free Operation Only) WARNING: Maintain the minimum clearances. If you can, provide greater clearances from floor, ceiling, and adjoining side and back walls. Back Wall 6 " Minimum Carefully follow the instructions below. This stove is a freestanding unit designed to set directly on the floor. IMPORTANT: You must maintain minimum wall and ceiling clearances during installation. The minimum clearances are shown in Figure 4. Measure from outermost point of stove top. Minimum Wall and Ceiling Clearances (see Figure 4) A. Clearances from outermost point of stove top to any combustible side wall should not be less than 12 inches. B. Clearances from outermost point of stove top to any combustible back wall should not be less than 6 inches (Includes Corner Installations). C. Clearances from the stove top to the ceiling should not be less than 48 inches. Side View Front View Top View 12" Minimum 12" Minimum 48" Minimum Ceiling Side Wall Side Wall Front of Stove Unit Side Wall Side Wall 12 " Minimum 12 " Minimum 6" Minimum 48" Minimum Ceiling Floor Back Wall Corner Wall Wall 6 " Minimum 6 " Minimum Figure 4 - Minimum Clearance to Walls and Ceiling (Stove May Vary Depending on Model) Continued 104463 7 VENT-FREE NATURAL GAS STOVE HEATER INSTALLATION Continued STOVE CAVITY ASSEMBLY 1. Lift off corrugated box enclosing stove body crating. 2. Remove all screws fastening the wood frame enclosure. Spread wood frame open and lift away from plastic-bagged stove body. The bottom pieces of pallet wood will remain bolted to the stove body. 3. Remove plastic bag from stove body. 4. Remove back panel from stove (see Figure 5). Use an adjustable wrench or a 10 mm socket. Remove six (6) bolts and washers. Keep bolts and washers to reattach back panel later. 5. Remove all contents from inside stove cavity. Contents include: (1) - Stove bottom (4) - Legs (Amity models include leg leveler bolts) (1) - Bottom door (1) - Top grate (1) - Hardware kit bag with fasteners 6. Carefully lay stove body on back to attach bottom components to stove body (see Figure 6). Rest stove on drop cloth or blanket to avoid scratching stove edges. 7. Remove remaining pallet wood attached to bottom of stove body (see Figure 7). Use an adjustable wrench to remove bolts. 8. Fasten each leg to stove with four (4) bolts. Use a flat screw driver to tighten bolt to leg. Thread bolt in tapped holes on stove body (see Figure 8 and Figure 9, page 9). Bolt Product Back Stove Panel Identification Label Figure 5 - Removing Back Panel Top of Stove Unit Figure 6 - Laying Down Stove On Back (Stove Style May Vary Depending on Model) Front of Stove Unit Pallet Wood Bolted to Stove Body Bottom Front of Stove Unit Top of Stove Unit Drop Cloth/ Blanket Front Bolt Pallet Wood Figure 7 - Removing Pallet Wood From The Bottom of The Stove Door Hinge StepBolt Hole Bottom Of Stove Unit Pallet Wood Door Catch Bolt With Adjustable Front Hex Nuts Hole Leg Leg Hole Hole Bottom Of Stove Unit Leg Leg Hole Hole Stove Bottom Holes Figure 8 - Locating Threaded Holes for Stove Bottom, Legs, and Door Attachment (Appearance May Vary Depending on Model) 8 104463 104463 9 OWNER’S MANUAL INSTALLATION Continued Continued Figure 9 - Attaching Stove Legs Bottom Of Stove Unit Leg Bolt Figure 10 - Attaching Stove Bottom Bottom Of Stove Unit Bolt Washers Stove Bottom 9. Fasten stove bottom to stove with four (4) M6 x 1 - 25mm bolts. Use a flat washer and lock washer with each bolt. Tighten bolts into threaded holes on stove body (see Figure 8, page 8 and 10). Use an adjustable wrench or a 10mm socket. Figure 11 - Attaching Stove Door (Appearance May Vary Depending on Model) Step Bolt Door Hinge Threaded Hole Stove Door Bolt Stove Bottom Shoulder Door Hinge Step Bolt Bolt Shoulder Adjusting Nut Bolt Stop Catch Bolt Door Door Claw Figure 12 - Catch Bolt and Door Claw Orientation Stove Door 10. Attach stove door by inserting step bolt through door hinge pivot holes and into threaded hole in stove body (see Figure 11). Use an adjustable wrench or a 12mm socket to fasten step bolt. Tighten step bolt until snug. Make sure door moves freely. 11. Install door catch bolt (M8 x 1.25- 55mm with two M8 hex nuts) into threaded hole on stove body (see Figure 8, page 8). Use an a...