Attach with (2) Latch Screws and (2) Latch Nuts. Line up holes in Access Panel hinges with holes in recessed area of left leg. Attach each hinge with (2) Hinge Screws and (2) Hinge Nuts. Swing Access Panel closed and slip Latch over panel hook and snap shut. Step 15 - Replace Engine Assembly Slide Igniter wire onto Igniter post. Position Engine Access Panel back in place. Secure Panel in place with 3 screws previously removed from side and bottom holes. Note: Once you have successfully completed assembly steps 1-15 you are ready to begin operating your heater. Owner's manual: model 163000 outdoor patio heater 12/15/03 12 Endless Summer- Contact 1-800-762-1142 for assistance. Do not return to place of purchase. A WARNING FOR YOUR SAFETY • Do NOT attempt to operate heater until you have read and understand all precautions in Section 1 “Safety First.” Failure to do so can result in serious personal injury, death, or property damage. • If at any time you are unable to light burner and smell gas, wait 5 minutes to allow gas to dissipate before attempting to light heater. • Do NOT touch emitter or dome or move heater for at least 45 minutes after use. 13 Operation Caution: Do NOT attempt to operate heater until you have read and understand all precautions in section 1 “Safety First.” Before Turning Gas Supply ON • Your heater was designed and approved for OUTDOOR USE ONLY. DO NOT use it inside a building, garage, or any other enclosed area. • Make sure surrounding areas are free of combustible materials, gasoline, and other flammable vapors or liquids. • Ensure that there is no obstruction to air ventilation. • Be sure all gas connections are tight and there are no leaks. • Be sure the access panel is clear of debris. • Be sure any component removed during assembly or servicing is replaced and fastened prior to starting. Before Lighting • Heater should be thoroughly inspected before each use, and by a qualified service person at least annually. • If relighting a hot heater, always wait at least 5 minutes. • Inspect the hose assembly for evidence of excessive abrasion, cuts, or wear. Suspected areas should be leak tested. If the hose leaks, it must be replaced prior to operation. Only use the replacement hose assembly specified by manufacturer. Lighting Note: This heater is equipped with a Pilot Light that allows for safer startups and shutdowns. Pilot must be lit before Main Burner can be started. • Turn Cylinder Valve OFF. • Push Control Knob IN and turn to OFF. • Wait 5 minutes for any gas to clear. • Turn Cylinder Valve ON. • Open Viewing Hole by sliding cover to either side. • Push Control Knob IN and rotate to Pilot position. • Note - For initial start or after any cylinder change, hold Control Knob IN for 2 minutes to purge air from gas lines before proceeding. • Push Igniter button once. Pilot Light flame will appear and be visible through Viewing Hole. • Release Control Knob after 30 seconds. Pilot Light will remain lit. If not, return to step 1. • Turn Control Knob to ON. Main Burner will light immediately. Flame is visible through Viewing Hole. If not, return to step 1. Owner's manual: model 163000 outdoor patio heater 12/15/03 Contact 1-800-762-1142 for assistance. Do not return to place of purchase. Endless Summer- V • If for some reason your ignitor fails to deliver a spark, your heater can be started by inserting a lit match through the pilot view hole while pushing the control knob in while in the PILOT position. If you experience any ignition problem consult “Troubleshooting” on page 16. Caution: Avoid inhaling fumes emitted from the heater’s first use. Smoke and odor from the burning of oils used in manufacturing will appear. Both smoke and odor will dissipate after approximately 30 minutes. The heater should NOT produce thick black smoke. Note: The burner may be noisy when initially turned on. To eliminate excessive noise from the burner, turn the Control Knob to the Pilot position. Then, turn the knob to the level of heat desired. A WARNING FOR YOUR SAFETY Be careful when attempting to manually ignite this heater. Holding in the control know for more than 10 seconds before igniting the gas will cause a ball of flame upon ignition. When heater is ON: Emitter screen will become bright red due to intense heat. The color is more visible at night. Burner will display tongues of blue and yellow flame. These flames should not be yellow or produce thick black smoke, indicating an obstruction of airflow through the burners. The flame should be blue with straight yellow tops. If excessive yellow flame is detected, turn off heater and consult “Troubleshooting” on page 16. Re-lighting Note: For your safety, Control Knob cannot be turned OFF without first depressing Control Knob in PILOT position and then rotating it to OFF. Turn Control Knob to OFF. Wait at least 5 minutes, to let gas dissipate, before attempting to relight Pilot. Repeat the...