Votes - , Average rating:
(
)
)
Manafacture: Blue Rhino
File size: 1.12 mb
File name: 15c7a929-d9f5-4042-93fb-5cca9a568602.pdf
Language of manual:
The document is loading, please wait
 |
The document is loading, please wait
manual abstract
Step 1 – Attach Emitter Screen • Line up 4 holes on bottom of Emitter Screen with corresponding holes in Emitter Bottom, and insert (4) Medium Screws in holes until tight. Owner’s manual and assembly instructions: 81000 portable outdoor heater 3/3/03 6 Contact 1-800-762-1142 for assistance. Do not return to place of purchase. Step 2–Attach Top Wire Guard • Line up 4 prongs on Wire Guard Bottom with 4 holes on Emitter Bottom, and Insert. Note: It may be necessary to adjust the prongs slightly to line them up with the holes. Step 3–Attach Dome to Emitter • Line up three studs in Emitter with holes in Dome. Slide Dome carefully over studs, clamping Top Wire Guard securely in place. Note: It may be necessary to adjust prongs of the Top Wire Guard slightly to provide a secure fit. • Install (3) Nuts on studs and tighten with 7/16” wrench. Do not over tighten. Step 4–Attach Dome Cap • Lay Dome Cap on Dome covering 3 Nuts and line up center holes. • Insert threaded end of Finial through Cap and screw into center of Dome until secure. Contact 1-800-762-1142 for assistance. Do not return to place of purchase. Notice Do not use tools to tighten the thumbscrew. Hand tighten only. Do not over tighten to prevent possible damage to table surface. Caution: Before you attempt to use a propane cylinder, understand all cylinder and propane related precautions in Section #1 – “Safety First.” Step 5–Center Lockup • Slide the threaded portion of the large thumbscrew through the slot in the center of the bracket mounted to the base. • Thread the bottom bracket on to the thumbscrew with the round flat rubber pads facing up. • To mount the heater to a hole in your table, tilt the bottom bracket/thumbscrew assembly until it fits through the hole. Straighten the thumbscrew, and pull it up until the rubber pads contact the underside of the table. Hand tighten only. Note: If the hole in the surface you are mounting your heater to is less than 1-1/2” in diameter, it will be necessary to center your heater over the hole and slide the thumbscrew through the slot in the bracket and the hole in the table. Attach the bottom bracket from underneath, and tighten from the top with the thumbscrew. Step 6 – Gas Hook-up Note: For best results, use heater with a 20 lb. cylinder. The pressure regulator and hose assembly supplied with the appliance must be used and replacements must be those specified by the manufacturer. To connect 20 lb. Cylinder • Slip end of flexible gas line with brass fitting through center hole of Base and up to threaded portion of regulator. • Line up threads on fitting with those on regulator and rotate clockwise until snug. HAND TIGHTEN ONLY. DO NOT USE ANY HAND TOOLS TO MAKE THIS CONNECTION. BE CAREFUL NOT TO CROSS THREADS WHEN SCREWING IN FITTING. Note: if heater uses center clamp, hose can be routed through opening in base and table. • Set heater on base, making sure that flexible gas line is routed through small slot in base. • Attach gas line to cylinder by turning black plastic knob counter clockwise into cylinder valve until tight. Note: Be careful not to kink flexible gas line. • When using the gas extension hose always locate the hose out of pathways where people may trip over it or in areas where the hose may be subject to accidental damage. To connect 14.1 oz or 16.4 oz cylinder Note: Some 1-lb cylinders may form frost when near empty. • Line up threads on canister with those on regulator, insert and rotate canister clockwise until they fit snugly together. HAND TIGHTEN ONLY. BE CAREFUL NOT TO CROSS THREADS WHEN SCREWING IN CANISTER. 7 Owner’s manual and assembly instructions: 81000 portable outdoor heater 3/3/03 Contact 1-800-762-1142 for assistance. Do not return to place of purchase. Step 7 – Check for Leaks To check for leaks: • Make 1-2 oz. of leak solution by mixing one part liquid dishwashing soap and 3 parts water. • Spoon several drops (or use squirt bottle) of the solution onto the regulator/canister connections. • Inspect the connections and look for bubbles • If NO bubbles appear, the connection is safe. • If bubbles appear, there is a leak: • Loosen and re-tighten this connection. • Re-check for a leak. • If you continue to see bubbles after several attempts, disconnect propane source and contact 1-800-762-1142. Caution: Your Endless Summer Portable Heater has been checked at all factory connections for leaks. Recheck all connections, as movement in shipping can loosen connections. Check for leaks even if your unit was assembled for you at the store. Step 8 – Install Access Panel • Slide top tab of Access Panel inside Shroud Cover. • Lower bottom of Panel until closed, and rotate Knob until lock flange rotates inside of slot on plastic ring. Owner’s manual and assembly instructions: 81000 portable outdoor heater 3/3/03 Contact 1-800-762-1142 for assistance. Do not return to place of purchase. Step 9 – Securing the Tank Mount your 20 lb. cylinder to a sturdy object such as a table or post within 3 to...