Votes - 4, Average rating: 3.3
(
)
)
|
manual abstract
Thread manifold to bottom of burner assembly (see Figure 9). Tighten with wrenches (see Figure 10.) 10. Temporarily connect hose and regulator to manifold. Connect hose and regulator to a 20 lb. propane cylinder. DO NOT LIGHT HEATER! Open propane cylinder valve. Leak test burner assembly and manifold connection using a noncorrosive leak detection fluid. DO NOT USE FLAME. See Checking for Leaks, page 8. When there is no sign of a leak, turn off propane/LP cylinder valve and disconnect regulator from propane/LP gas cylinder. Slowly loosen connection between manifold and hose and regulator assembly. Propane gas left in hose will escape. 11. Remove bolts from burner assembly. Carefully lean base and pole assembly over and insert manifold and burner assembly through pole (see Figure 11). Replace bolts. 12. Remove blue film from dome top. Dome attaches to burner assembly with three 5/16" nuts and six 5/16" washers. Place 1 washer on each threaded stud of burner assembly. Place dome over studs. Attach 3 washers and nuts to studs. See Figure 12. Assembly Continued Burner Assembly Manifold Burner Assembly Bolts Removed From Here Manifold Pole Bolts Reinstalled Through Here Figure 11 - Sliding Manifold and Burner Assembly into Pole Figure 9 - Attaching Manifold to Burner Assembly Figure 10 - Tightening Manifold and Burner Assembly Figure 12 - Attaching Dome to Burner Assembly 13. Remove tank door. Wrench tighten regulator and hose assembly to manifold as shown in Figure 13. Check connections for gas leaks (see Checking for Leaks). Note: Make sure hose and regulator assembly attached to manifold are never bent or kinked during installation and operation of heater. 14. Place propane/LP tank on top of base. Attach regulator. 15. Install propane tank safety chain around tank and into openings on legs as shown in Figure 14. 16. Reinstall door. Checking for Leaks IMPORTANT: The heater must be leak tested before any further assembly is done. Use only a noncorrosive leak detection fluid. DO NOT USE FLAME. Turn control knob to the OFF position. Securely connect regulator to propane/LP gas cylinder. Open propane/LP cylinder valve. Apply a noncorrosive leak detection fluid to connections at the manifold and regulator connections. Bubbles forming show a leak. In case of any leaks, turn off propane/LP cylinder valve, remove manifold, check and clean connection. Reconnect manifold and leak test again. Upon completion of leak test, and when there is no sign of a leak, turn off propane/LP cylinder valve and disconnect regulator from propane/LP gas cylinder. Remove propane/LP gas cylinder and continue to next step. Assembly Continued Safety Chain Cap Support Figure 14 - Propane Tank and Safety Chain Figure 13 - Attaching Regulator and Hose Assembly Locating Heater WARNING: Do not move heater when lit. Allow heater to cool before moving. 1. Locate pop-out wheel decal on base of heater (see Figure 15). 2. Standing on decal side of heater, carefully lean heater away from you to access wheels underneath base. 3. Swing wheels out from under base to relocate heater. 4. Replace wheels underneath base after placing heater in desired location. Pop-out Wheel Decal Figure 16 - Locating Heater Wheel Figure 15 - Pop-out Wheels Operation WARNING: If you smell gas: • Shut off gas to the appliance. • Extinguish any open flames. • If odor continues, immediately call your gas supplier. See safety warnings and precautions starting on the front page of this manual for more information. PREPARING FOR OPERATION 1. Check heater for possible shipping damage. If any is found, immediately notify dealer. 2. Follow all safety information starting on page 2. 3. Check and assure control knob is in the OFF position. 4. Place propane/LP gas cylinder inside cylinder base. Securely connect regulator to propane/LP gas cylinder. 5. Turn cylinder valve on. Apply a noncorrosive leak detection fluid to connection at regulator and cylinder. Bubbles forming show a leak. 6. In case of any leaks, turn off propane/LP cylinder valve, undo leaking connection. Check and clean connection. Reconnect regulator and leak test again. IMPORTANT: On new installations or routine gas cylinder changes. The system must be purged of air before use. Turn control knob to the pilot setting. Press and hold for 30-40 seconds before attempting to light pilot. TO LIGHT 1. Shut main gas supply valve on propane cylinder off. Set heater control knob to OFF position. Wait 5 minutes. 2. Open main gas supply valve on propane cylinder. 3. Turn heater control knob to the PILOT position. Push and hold for 5 seconds. Press igniter button until pilot is lit. Continue to hold heater control valve for 30 seconds then release. CAUTION: Do not attempt to slide viewing hole cover when main burner is lighting, operating or hot. 4. TO MATCH LIGHT PILOT: Rotate match light hole cover. Apply flame to pilot burner while holding knob in for 20 seconds or until pilot remains lit when knob is released. 5. Knob can now be t...