Login:
Votes - 2, Average rating: 3.5 ( )

User manual Melissa, model 670-206

Manafacture: Melissa
File size: 1.33 mb
File name: eb63d077-764f-403e-8f55-5c37aba25c02.pdf
Language of manual:plsvendedafi
Free link for this manual available at the bottom of the page



manual abstract


Bracket, rear n. Screws and nuts for bracket o. Mounting screw A wall bracket together with rawlplugs and screws are included with the wall-mounted model. Certain models also have remote control and waterproof cover. POSITIONING THE APPLIANCE Wall-mounted model (670-206/208) • The heater head (1) should be at least 30cm from the ceiling, 30 cm from any side wall, and at least 1.8m above the floor. • Use the wall bracket supplied for wall mounting. Do not use other brackets or fittings. • Screw wall bracket to wall as illustrated. The angled section of the bracket should face upwards. • Hang the heater head on the wall bracket. Mount hanging bracket (13) at the top of the rear of the heating head on angled part of wall bracket. Insert retaining screw in hole in wall bracket base, and tighten securely. • Check that the appliance is firmly fixed in place before using it. Models with tent bracket (model 670-209/211) • The heater head (1) should be at least 30cm from the tent ceiling or parasol cover, 30 cm from any side wall, and at least 1.8m above the floor. • Use the tent bracket supplied for mounting. Do not use other brackets or fittings. • Mount tent bracket front (l) and rear sides (m) on a tent or parasol pole as illustrated. Use the screws and nuts supplied (n). • Mount curved bar (k) into socket on front of bracket using the retaining screws supplied (o). UK • Mount heating head on curved bar so that hole in bar is aligned with hole in heating head. Secure using mounting screw. • Check that the appliance is firmly fixed in place before using it. Models with stand (model 670-207/209/211) • The appliance should be sited at least 1m from the nearest wall. The heater head should be at least 30cm from the ceiling, and at least 1.8m above the floor. The appliance should stand firmly on a horizontal floor. • Fit lower part of stand (b) in base (a), lay base on its side, and fasten stand to underside of base with washer and screw (c) (See illus. I). • Position base correctly so that stand is upright. Slacken screw (c) in middle of stand (d), and insert middle part into lower part. Align screw with recess in lower part (see illus. II). Tighten screw. In the same way, fix upper part of stand (e) in middle part with a screw (see illus. III). • Extend thin rod (f) from sleeve (g) at top of rod to desired height. Fit cuff (h) over thin rod. Tighten cuff (see illus. IV). • Mount heating head on thin rod so that hole in the rod is aligned with hole in heating head. Secure using mounting screw (14) (see illus. V). Tighten all screws thoroughly. • Check that the appliance is standing firmly in place before using it. • The cable may be secured in the cable holder (j) on the stand. • The curved stand can be rotated 360° so that the heating head can face in any direction. OPERATING THE APPLIANCE • If the appliance has a stand, angle and height of heating head can be adjusted. o Set head at desired angle by turning the hinge (12). o Set head at required height ...

Other models in this manual:
Electric Heaters - 670-207 (1.33 mb)
Electric Heaters - 670-208 (1.33 mb)
Electric Heaters - 670-209 (1.33 mb)
Electric Heaters - 670-211 (1.33 mb)

Reviews



Your review
Your name:
Please, enter two numbers from picture:
capcha





Category