Votes - , Average rating:
(
)
)
Manafacture: Cadet
File size: 221.97 kb
File name: 1047.pdf
Language of manual:
The document is loading, please wait
 |
The document is loading, please wait
manual abstract
When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following: Tel: 360-693-2505 P.O. Box 1675 Vancouver, WA 98668-1675 9. WARNING Risk of electrical shock. Connect to properly grounded outlets only. Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage the heater. Unplug heater before performing any maintenance or when not in use. To disconnect heater, turn control to lowest position, then remove plug from outlet. 10. WARNING Risk of electrical shock or injury. Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or the like. Do not route cord under furniture or appliance. Arrange cord away from traffic area where it will not cause a tripping hazard. Do not operate heater with a damaged cord or plug, or after heater malfunctions, or has been dropped or damaged in manner. Discard heater, or return to authorized service facility for examination and/or repair. 11. WARNING Risk of Fire. To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on soft surfaces, like a bed, where openings may become blocked. Heater must be kept clear of all obstructions: maintain a 3 foot minimum clearance from front and 12 inches from sides and rear. Heaters must be kept clean of lint, dirt and debris. (See Maintenance Instructions) 12. Always plug heaters directly into a wall outlet/receptacle. Never use with an extension cord or relocatable power tap (outlet/power strip). 13. Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electrical shock, or injury to persons. 14. WARNING Risk of Fire. Do not use as a residential or household heater. 15. When heater is wall or ceiling mounted, the anchoring provisions must be strong enough to support the total weight of the heater and heater mounts. Failure to properly secure the supports to the building structure could allow the heater to fall. 1. Read all instructions before using this heater. 2. Do not place heater against paperboard or low-density fiberboard surfaces. 3. Do not use outdoors. 4. This heater is not intended for use in bathrooms, laundry areas and similar indoor or very humid locations. Never locate heater where it may fall into a bathtub or other water container. 5. Do not place heater below an electrical convenience receptacle. 6. WARNING Overheating or fire may occur. Do not place the heater behind doors. 7. WARNING Fire or explosion may occur. Heater has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint, or flammable liquids are used or stored. 8. WARNING Burn Hazard. This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. If provided, use handles when moving this heater. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9 m) from the front of the heater and 12 inches from sides and rear. Use extreme caution when any heater is used by or near children or invalids and whenever the heater is left operating unattended. Front Back Grounding Instructions Grounding Instructions This heater is for use on 240 (or 208) volts. The cord has a plug as shown to the right. No adapter is available for this blade configuration, and none should be used. The outlet type is a 240 (or 208) volt grounding outlet. When properly installed, it provides a ground connection through the cord to the heater to protect the operator from electrical shock. CGH562 – 30 AMP Receptacle Configuration Plug Configuration Installation Instructions CAUTION: Heater will operate on either 240 or 208 volts. Check heater voltage and phase on label on back of heater to make sure they are the same as the electrical service supplied. See plug configuration. Altering the cord in any way will void the warranty! Be sure that the electrical receptacle is of the configuration and capacity appropriate for the heater. Floor Application This heater may be used for floor or flat surface mounting. After placing the heater on floor or other flat surface in an appropriate location, insert plug into the proper type wall outlet. Wall or Ceiling Mount Application Heater can be mounted on wall or ceiling with proper anchoring provisions. The wall/ceiling mounting structure and anchoring provisions must be of sufficient strength to support the combined weight of the heater and mounting bracket. Specifications MODEL WATTS VOLTS (60 Hz) BTUs AMPS PLUG TYPE CGH562 5600 / 4200 240 / 208 19,107 / 14,322 23.4 / 20.2 30 Amp Operation and Maintenance How To Operate Your Heater 1. Turn the thermostat knob fully clockwise . 2. When the room reaches your comfort level, turn the thermostat knob counter clockwise until the heater shuts off. One or two minor adjustments may be necessary as...