Votes - 4, Average rating: 3.8
(
)
)
|
manual abstract
For localized language versions of this document, go to Assembling the 4800dr Place arm on tray. Use the 3 screws provided to attach the arm to the underside of the tray. 1 Place the imager in the stand. Press the cable firmly into the wire run along the back of the arm. (You must use the USB cable that's supplied with the 4800dr or a compatible 5 volt powered cable.) 2 Imager Mounting Details If you are planning to mount the imager in a fixed position, the following diagram shows the mounting hole placement and details. All measurements are in inches. Connecting to the Host Turn off computer's power before connecting the document reader, then power up the computer once the document reader is fully connected. USB Connection 3 TTL-232 Connection U 4 Interface Scan the barcode that describes the PC or interface you are using. USB Keyboard (PC) USB Keyboard (Mac) USB Japanese Keyboard (PC) USB HID Barcode Reader USB COM Port Emulation TTL-232 Interface Aligning the Document Reader Tray Proper cable placement is important for accurate alignment of the device. Place the cable in the wire channel if the imager will remain in the base most of the time. If you plan to frequently lift out the imager to scan items, then set the cable in the location where it will rest while the imager is in the stand. Note: The 4800dr will not capture any images until it has been properly aligned using the following procedure. 1. Loosen the screw in the base tray with a coin. 2. Place the alignment page on the tray. Align the upper left corner of the alignment page to the upper left corner of the tray. 5 ~PAP124. ~PAP125. ~TERMID134. ~PAP131. ~TERMID130. ~PAP232. 3. Make sure the serial number on the alignment page (the top number) matches the serial number on your document reader. 4800dr s/n—► 07i50Aisi:i engine s/n —► CP:57AiC3u 4. Press the button on the imager to display the illuminated aimer crosshairs. You will hear a single beep that indicates you are using the correct page. (If you hear 3 beeps and the aimer turns off, then you have the wrong alignment page for your document reader.) 5. Move the tray until the illuminated aimer crosshairs line up with the printed crosshairs on the alignment page. (Be sure to wait until the crosshairs go off before removing power or attempting to capture an image.) 6. Remove the alignment page and tighten the screw. Save the alignment page in the event that the tray needs to be realigned in the future. Note: If you need to print a new copy of the alignment page, make sure to print the page in landscape mode. Imaging Technique Center a document in the document reader tray. (Smaller documents should be centered in the pocket in the tray.) Press the button on the imager. The view finder projects an aiming beam to indicate the image capture area. Technical Assistance If you need assistance installing or troubleshooting, please call your Distributor or the nearest Hand Held Products technical support office: North America/Canada Telephone: (800) 782-4263 Fax number: (315) 554-6705 E-mail: natechsupport@handheld.com Latin America Telephone: (803) 835-8000 Telephone: (800) 782-4263 E-mail: latechsupport@handheld.com Brazil Telephone: +55 (21) 3535-9100 Fax: +55 (21) 3535-9105 E-mail: brsuporte@handheld.com Mexico Telephone: (803) 835-8000 E-mail: latechsupport@handheld.com 6 Europe, Middle East, and Africa Telephone: +31 (0) 40 7999 393 Fax: +31 (0) 40 2425 672 E-mail: eurosupport@handheld.com Asia Pacific Telephone - Hong Kong: +852-3188-3485 or 2511-3050 Telephone - China: +86 21 6361 3818 E-mail: aptechsupport@handheld.com Japan Telephone: +813 5770-6312 E-mail: aptechsupport@handheld.com Malaysia Telephone: +603-6201-7020 E-mail: aptechsupport@handheld.com Online Technical Assistance You can also access technical assistance online at For Further Information To download the full User's Guide for these products, visit our website at Product Service and Repair Hand Held Products provides service for all its products through service centers throughout the world. To obtain warranty or non-warranty service, return the unit to Hand Held Products (postage paid) with a copy of the dated purchase record attached. Contact the appropriate location below to obtain a Return Material Authorization number (rMa #) before returning the product. North America Telephone: (800) 782-4263 Fax: (803) 835-8012 E-mail: naservice@handheld.com Latin America Telephone: (803) 835-8000 Telephone: (800) 782-4263 Fax: (239) 263-9689 E-mail: laservice@handheld.com Brazil Telephone: +55 (21) 3535-9100 Fax: +55 (21) 3535-9105 E-mail: brservice@handheld.com Mexico Telephone: +52 (55) 5203-2100 Fax: +52 (55) 5531-3672 E-mail: mxservice@handheld.com 7 Europe, Middle East, and Africa Telephone: +31 (0) 40 2901 633 Fax: +31 (0) 40 2901 631 E-mail: euservice@handheld.com Asia Pacific Telephone: +852-...