Votes - 2, Average rating: 3.5
(
)
)
|
manual abstract
For the wall mounting instructions follow the illustrated steps ‘ to § printed on the separate template. Make sure that the wall mount is being fixed securely enough so that it meets safety standards.The weight of the monitor (excl. packaging) is about 36 kg. Note: Stands are optional accessories. Consult your dealer. To prevent any unsafe situations, no naked flame sources, such as lighted candles,should be placed on or in the vicinity.Avoid heat,direct sunlight and exposure to rain or water. The equipment shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on it. Connect your computer Directly to the monitor & Connect one end of a VGA cable to the video card of the computer and the other end to the VGA 1 connector at the rear side of the monitor. Fix the connectors firmly with the screws on the plug. e In case of a multimedia computer, connect the audio cable to the audio outputs of your multimedia computer and to the audio inputs of your external amplifier. VGA 2:The video connector for VGA2 can be programmed to become an input or an output via the Setup menu, see p. 6.The function of being input or output is determined by the used mode. If the monitor is used in video mode, the VGA 2 connector is VGA output. If the monitor is used in monitor mode,the connector is VGA input or output. To an electronic receiver box See the handbook of the receiver box. & Connect one end of a VGA cable to the video card of the computer and the other end to the PC/MAC IN connector at the rear side of the receiver box. Fix the connectors firmly with the screws on the plug. e In case of a Multimedia computer, connect the audio cable to the audio outputs of your Multimedia computer and to the AUDIO IN R and L inputs of the receiver box. For sound reproduction, connect your external amplifier to the electronic receiver box. Note: Only use the VGA cable supplied with the monitor. Daisy chaining The Loop Through facility makes it possible to make a daisy chain with a second monitor. Connect one end of another VGA cable to the VGA 2 connector at the rear side of the monitor and the other end to the VGA 1 connector of a second monitor. The RC out jack next to the VGA 2 connector makes it possible to daisy chain remote control signals to other equipment.This output cannot be used to daisy chain a second monitor. Serial I/O port RS232 The RS232 connector is only to be used with the monitor as stand alone. This connector allows you to control the monitor via your PC (as a replacement of the remote control). Note:This connector can also be used for dealer service tools. Use of the remote controlComputer Display modes VGA 640x480 60, 72, 75, 85 Hz Wide VGA 848x480 60 Hz Wide VGA 852x480 60 Hz MAC 640x480 66.67 Hz MAC 832x624 74.55 Hz MAC 1024x768 74.93 Hz MAC 1152x870 75 Hz SVGA 800x600 56, 60, 72, 75, 85 Hz XGA 1024x768 60, 70, 75, 85 Hz SXGA 1280x1024 60, 72 Hz When a VGA computer is connected, the display selection is made automatically. A message is displayed when the monitor does not support the connected VGA mode. Switch your computer to a correct display mode. Operation R6 / AA B & Insert the mains plug supplied into the mains inlet at the back of the monitor and in the wall socket. Please, only use the supplied rim-earthed mains cord which has to be inserted in a grounded socket. e Remote control: remove the cover of the battery compartment. Insert the 2 batteries supplied (Type LR6/AA-1.5V). The batteries supplied do not contain the heavy metals mercury and cadmium. Nevertheless in many countries batteries may not be disposed of with your household waste. Please check on how to dispose of batteries according to local regulations. “ Make sure that your receiver box and/or PC are switched on and that your PC is in the correct display mode. ‘ Switch the monitor on : Press the power button B at the right side of the monitor. A green indicator lights up and the screen comes on. When the monitor does not receive a supported VGA signal and is not connected to a receiver box the screen switches to standby and the red indicator lights up. When you switch on your monitor for the first time, and the monitor is not connected to an electronic receiver box, the menu language automatically appears on the screen.The explanation appears in different languages one at a time. Follow the instructions on screen to select the correct language or see Setup menu, Language, p. 6. POWER BRIGHTNESS CONTRAST ZOOM OUTZOOM INZOOM ON/OFF VGA AV1 AV2 AV3 MUTE AV MUTE q 1 2 3 4 5 6 7 8 9 0 V CH/PR MENU OK ¬ B VGA press repeatedly to select your computer connected to the VGA 1 or 2 connector. AV1, AV2, AV3 press to select the peripherals connected to the connector indicated on the monitor. V no function (except when in combination with an electronic receiver box. ¬ no function (except when in combination with an electronic receiver box. CH/PR Program selection To browse through the sources selected. B...