Votes - 0, Average rating: 0
(
)
)
|
manual abstract
Cleaning and maintenance Never use compressed air, scouring pads, abrasive cleaning agents or aggressive liquids such as petrol or acetone to clean the shaver, the charging stand (PT927/PT925/PT923/PT920/PT876/PT875 only) and the Jet Clean System (PT927CC/PT923CC only). - The best and most hygienic way to clean the shaver is in the Jet Clean System (PT927CC/PT923CC only).You can also rinse the shaver under the tap or clean it with the cleaning brush supplied. -Clean the shaver after ever y shave for optimal shaving performance. -Regular cleaning guarantees better shaving performance. - For the best cleaning results, we advise you to use the Philips Cleaning spray (HQ110) and (PT927CC/PT923CC only) the Jet Clean solution (HQ200). - Be careful with hot water. Always check if the water is not too hot, to prevent your hands from getting burnt. Note:Water may leak from the socket at the bottom of the shaver when you rinse it.This is normal and not dangerous because all electronics are enclosed in a sealed power unit inside the shaver. Cleaning the shaving unit under the tap 1 2 3 Switch off the shaver and disconnect it from the mains. Press the release button to open the shaving unit. Rinse the shaving unit and hair chamber under a hot tap for 30 seconds. Be careful with hot water. Always check if the water is not too hot, to prevent your hands from getting burnt. 12 English -Rinse the hair chamber and the inside of the shaving unit. -Rinse the outside of the shaving unit. 4 Close the shaving unit and shake off excess water. Be careful not to hit the shaving unit against anything while shaking off excess water. Never dry the shaving unit and the hair chamber with a towel or tissue, as this may damage the shaving heads and the coupling spindles. 5 Open the shaving unit again and leave it open to let the shaver dry completely. Cleaning the shaving unit with the cleaning brush A 1 2 Switch off the shaver and disconnect it from the mains. Press the release button to open the shaving unit. 3 Pull the shaving unit off the shaver. 4 Turn the lock anticlockwise (A) and remove the retaining frame (B). 5 Remove and clean one shaving head at a time. Each shaving head consists of a cutter and a guard. Note: Do not clean more than one cutter and guard at a time, since they are all matching sets. If you accidentally mix up the cutters and guards, it may take several weeks before optimal shaving performance is restored. -- Remove the cutter from the shaving guard and clean it with the brush. -- Clean the inside and outside of the shaving guard with the brush. 6 Put the shaving heads back into the shaving unit. Note: Make sure that the projections of the shaving heads fit exactly into the recesses. 7 Put the retaining frame back into the shaving unit (A)and turn the lock clockwise (B). 8 Insert the lug of the shaving unit into the slot in the top of the shaver. Then close the shaving unit. Note: If the shaving unit does not close smoothly, check if you have inserted the shaving heads properly and if the retaining frame is locked. English 13 14 English Cleaning the shaving unit in the Jet Clean system (PT927CC/PT923CC only) The Jet Clean System cleans the shaving unit. Preparing the Jet Clean system for use Note: Fill the cleaning chamber before first use and when the ‘fluid low’ symbol flashes to indicate that the fluid level is too low.When the fluid level drops below the minimum level, the cleaning symbol and the ‘fluid low’ symbol start to flash and the shaver holder returns to its starting position 1 Simultaneously press the release buttons on both sides of the cleaning chamber (A).Then lift the Jet Clean System off the cleaning chamber (B). The cleaning chamber remains behind. ,2 Unscrew the cap from the bottle with Jet Clean solution (HQ200) and remove the airtight seal. 3 Fill the cleaning chamber with Jet Clean solution (HQ200) up to the MAX indication. Note: Make sure the cleaning chamber is always filled above the MIN indication. 4 Place the Jet Clean System back onto the cleaning chamber (‘click’). Make sure that the release buttons snap back into place. When the cleaning chamber is filled with Jet Clean solution, do not move it to prevent leakage. 5 Put the small plug in the Jet Clean System and put the adapter in the wall socket. The shaver holder automatically moves to its highest position. , The Jet Clean System is now ready for use. using the Jet Clean system 1 Place the shaver without protection cap upside down in the shaver holder. Push down the locking lever completely to lock the shaver into place. The battery symbol on the Jet Clean System goes on to indicate that , the shaver is being charged. Note:The shaver cannot be placed in the Jet Clean System when the protection cap is on the shaving unit. English 15 2 Press the on/off button on the Jet Clean System to start the cleaning program. The battery symbol on the Jet Clean System goes out. , During the cleaning program, the cleaning symbol starts to flash ...