Votes - , Average rating:
(
)
)
Manafacture: Philips
File size: 4.06 mb
File name:
Language of manual:
The document is loading, please wait
 |
The document is loading, please wait
manual abstract
-When all lights burn green, the batter y is 100% charged. -When the bottom light burns green, 20% of the batter y capacity is left. Battery running low When the battery is running low, the bottom , light turns red. When you switch off the shaver, this light flashesblinks a few times. Cordless shaving time A fully charged shaver has a cordless shaving time of up to 55 minutes. charging the appliance Charge the shaver when the bottom light burns or flashes red. Do not recharge the shaver in a closed pouch. 1 2 3 when the battery has been fully charged. Put the appliance plug in the shaver. Put the powerplug in the wall socket. Remove the powerplug from the wall socket and pull the appliance plug out of the shaver Charging stand You can also charge the appliance by placing it in the charging stand, if provided. EnglisH Place the shaver properly in the plugged-in charging stand. Lift the shaver from the stand without tilting it. Using the appliance Shaving 1 Switch the shaver on by pressing the on/off button once. The blue light ring around the on/off button goes on to indicate that the motor is running. Note:When you switch the shaver on, all lights go on and then the remaining battery capacity is shown for a few seconds. 2 Move the shaving heads quickly over your skin, making both straight and circular movements. Shaving on a dr y face gives the best results. Your skin may need 2 or 3 weeks to get accustomed to the Philips shaving system. 3 Switch the shaver off by pressing the on/off button once. The blue light ring around the on/off button goes out. , , -- 8 EnglisH 4 Clean the shaver (see chapter ‘Cleaning and maintenance’). 5 Put the protection cap on the shaver every time you have used it, to prevent damage. trimming For grooming sideburns and moustache. 1 Open the trimmer by pushing the slide downwards. The trimmer can be activated while the motor is running. 2 Close the trimmer (‘click’). Cleaning and maintenance The light above the tap symbol starts flashing after every shave to remind you that the shaver needs to be cleaned (except when the bottomlight burns red). Regular cleaning guarantees better shaving performance. The normal way to clean the appliance is to rinse the shaving unit and the hair chamber with hot water ever y time you have used the shaver. , EnglisH Be careful with hot water. Always check if the water is not too hot, to prevent your hands from getting burnt. Note:Water may leak from the socket at the bottom of the appliance when you rinse it.This is normal and not dangerous. Every day: shaving unit and hair chamber 1 2 3 Switch off the shaver, remove the powerplug from the wall socket and pull the appliance plug out of the shaver. Press the release button to open the shaving unit. Clean the shaving unit and the hair chamber by rinsing them under a hot tap for some time. Make sure you clean the inside as well as the , outside of the shaving unit. 4 Close the shaving unit and shake off excess water. Never dry the shaving unit with a towel or tissue, as this may damage the shaving heads. 5 Open the shaving unit again and leave it open to let the appliance dry completely. You can also clean the hair chamber without water by using the brush supplied. Every six months: shaving heads 1 Open the shaving unit, turn the lock anticlockwise (1) and remove the retaining frame (2). 2 Clean the cutters and guards with the brush supplied. Do not clean more than one cutter and guard at a time, since they are all matching sets. If you accidentally mix up the cutters and guards, it may take several weeks before optimal shaving performance is restored. 3 Put the shaving heads back into the shaving unit. Put the retaining frame back into the shaving unit and turn the lock clockwise. 4 Close the shaving unit. Trimmer Clean the trimmer every time you have used it. 1 Switch off the shaver, remove the powerplug from the wall socket and pull the appliance plug out of the shaver. 2 Clean the trimmer with the brush supplied. 3 Lubricate the trimmer teeth with a drop of sewing machine oil every six months. 10 English EnglisH 11 Charging stand You can clean the charging stand with a moist cloth. storage Put the protection cap on the shaver to prevent damage. The appliance can be stored in the pouch supplied. The shaver can be stored in the charging stand, if provided. replacement Replace the shaving heads as soon as the light above the shaving unit symbol starts flashing. Replace damaged or worn shaving heads with HQ9 Philips shaving heads only. Note: Do not mix up the cutters and the guards to guarantee optimal shaving performance. 1 Switch the shaver off, remove the powerplug from the wall socket and pull the appliance plug out of the shaver. 2 Press the release button to open the shaving unit. ,, , , 12 EnglisH 3 Turn the lock anticlockwise (1) and remove the retaining frame (2). 4 Remove the shaving heads and place new ones in the shaving unit. Put the retaining frame back into the shaving unit and turn the...