Votes - 2, Average rating: 4.5
(
)
)
|
manual abstract
We hope you enjoy your new Braun Shaver. Warning Your Pulsonic shaving system is provided with a special cord set, which has an integrated Safety Extra Low Voltage power supply. Do not exchange or tamper with any part of it, otherwise there is risk of an electric shock. To prevent the cleaning fluid from leaking, ensure that the Clean&Renew station is placed on a flat surface. When a cleaning cartridge is installed, do not tip, move suddenly or transport the station in any way as cleaning fluid might spill out of the cartridge. Do not place the station inside a mirror cabinet, nor place it on a polished or lacquered surface. The cleaning cartridge contains a highly flammable liquid so keep it away from sources of ignition. Do not expose to direct sunlight and cigarette smoking nor store it over a radiator. Keep it out of reach of children. Do not refill the cartridge and use only original Braun refill cartridges. Description Clean&Renew station © Cleaning fluid display © Lift button for cartridge exchange ® Station-to-shaver contacts © «start cleaning» button © Cleaning program diodes © Station power socket © Cleaning cartridge Shaver © Foil & cutter cassette ® Cassette release button © Shaver head «lock» switch © Pop-out long hair trimmer ® On/off switch ® «reset» button ® Shaver display © Shaver-to-station contacts © Shaver power socket ® Travel case © Special cord set 4 Before shaving Prior to first use you must connect the shaver to an electrical outlet using the special cord set © or alternatively proceed as below. Installing the Clean&Renew station • Using the special cord set ©, connect the station power socket © to an electrical outlet. • Press the lift button © to open the housing. • Hold the cleaning cartridge © down on a flat, stable surface (e.g. table). • Carefully remove the lid from the cartridge. • Slide the cartridge into the base of the station as far as it will go. • Slowly close the housing by pushing it down until it locks. The cleaning fluid display © will show how much fluid is in the cartridge: «high» up to 30 cleaning cycles available «low» up to 7 cleaning cycles remaining «empty» new cartridge required Charging and cleaning the shaver Insert the shaver head down into the cleaning station. (The contacts © on the back of the shaver will align with the contacts ® in the cleaning station). If required, the Clean&Renew station will now charge the shaver. The hygiene status of the shaver will also be analyzed and one of the following cleaning program diodes © will light up: «clean» shaver is clean «eco» short economical cleaning required «normal» normal level of cleaning required «intensive» high intensive cleaning required 5 If the station selects one of the required cleaning programs, it will not start unless you press the «start cleaning» button ©. For best shaving results, we recommend cleaning after each shave. Whilst cleaning is in progress, the respective cleaning program diode will blink. Each cleaning program consists of several cycles, where cleaning fluid is flushed through the shaver head and a heat drying process dries the shaver. Depending on the program selected the total cleaning time will range from 32 to 43 minutes. The cleaning programs should not be interrupted. Please note that whilst the shaver is drying, the shaving head may be hot and wet. When the program is finished, the blue «clean» diode will light up. Your shaver is now clean and ready for use. Stand-by mode 10 minutes after completing the charging or cleaning session, the Clean&Renew station switches to the stand-by mode: The diodes of the Clean&Renew station and the shaver display turn off. Shaver display The shaver display ® shows the charge status of the battery. During charging or when using the shaver, the respective green battery segment will blink. When fully charged both charge segments will light up continuously, provided the shaver is switched on or connected to an electrical outlet. The red low charge segment flashes when the battery capacity has dropped below 20%, provided the shaver is switched on. The remaining capacity will then be sufficient for 2 to 3 shaves. Charging information • A full charge provides up to 50 minutes of cordless shaving time. This may vary according to your beard growth. • The best environmental temperature for charging is between 5 °C to 35 °C. Do not expose the shaver to temperatures higher than 50 °C for extended periods of time. 6 Shaving Press the on/off switch ® to operate the shaver: • The pivoting shaver head and floating foils automatically adjust to every contour of your face. • To shave hard to reach areas (e.g. under the nose) slide the shaver head «lock» switch ® to the back position to lock the pivoting head at an angle. • To trim sideburns, moustache or beard, slide the pop-out long hair trimmer © upwards. Tips for the perfect shave For best shaving results, Braun recommends you follow 3 simple steps: 1. ...