Votes - 3, Average rating: 4 ( )

Manafacture: Bosch File size: 830.89 kb File name: Language of manual:

preheated. (Preheat time should take approximately 12-15 minute when using 240 volts. If Mode Selector electrical supply is less than 240 volts preheat times will be longer). The light is connected to The mode selector knob is used to set the oven to the cooking elements and will turn off and on as Off, or for Self Clean, or to select the cooking the oven cycles to maintain the set temperature. function desired. A number of modes are available depending on the model oven you have purchased. Door Lock Light Please see Table 3, Cooking Function Settings, The door lock light will be illuminated whenever for information on selecting a cooking mode. the oven is in the self-clean mode and the door is locked. Cooking Function Settings Thermal Oven Function Information Broil -Used for broiling. When set on Broil the two top elements operate whenever heating. May be used with door open or closed. Bake (Roast) -This mode is used for baking, roasting and heating of casseroles, etc. When set on Bake Note: Lower element shown for the top element and the bottom clarity only. Lower ele-element operate whenever heating. ment actually is located below floor of cavity Convection Ovens have following additional cooking functions Convection Bake -The most versatile mode for baking and heating a variety of dishes. Also recommended for preparing large quantities of food on several racks. When set on Convection the rear circular bake element operates whenever heating. Fan operates. Convection Roast -Use for roasting. When set on Convection Roast the Note: Lower element shown for top element and the bottom clarity only. Lower ele-element operate whenever heating. ment actually is located Fan operates. below floor of cavity Convection Broil -Use of fish and broiling thick cuts of meat. The door must be closed when Convection Broiling. When set on Convection Broil both top elements operate whenever heating. Fan operates. Thaw -Use for defrosting. When set on Thaw no elements @ @ operate, only the fan is on. Table 3. Cooking Function Settings Oven Programmer The oven programmer can be used to electronically control the cooking in your oven. Figure 4 shows all the call-outs that are available on the display and their locations• The buttons directly adjacent to the display are the programming buttons. These are used to program the oven, including setting the clock. O Figure 4. Setting the Electronic Clock When you first turn on the power to your oven, or if the power to the oven has been off for a while the display will come on showing all the call-outs, as shown in Figure 4, and then will become blank, with dashes in the display area and the set clock symbol in the upper right of the programmer display, as shown in Figure 5. SET Figure 5. To set time of day Press in Set Clock button. A "beep" will be heard. Then press either the plus (+) or minus (-) button, to the right of the display, to set the correct time. If the plus (+) or minus (-) button is pressed it will advance or decrease the time in I minute increments, if the plus (+) or minus (-) button is held in the minutes will increase or decrease in 10 minute increments. Once the time is properly set depress the Set Clock button again to enter the time. A "beep" will sound and the Set Clock symbol, in the upper right, will disappear. To change the time of day simply repeat the steps described above. To check the time of day when the timer is in use depress the Set Clock button. The time of day will be displayed briefly and then will return to the timer function. Timer The timer acts as a kitchen timer, counting down from the set time. To Set Timer • Press Timer button. A "beep" will be heard and the display will change from showing the time of day to read zero (.00) and say SET TIMER, to the right, as shown in Figure 6. • Then press either the plus (+) or minus (-) button, to the right of the display, to set the timer to the time interval desired. SET TIMER Figure 6. Notes: 1. Each time the plus (+) or minus (-) button is depressed the display will increase or decrease in 1 minute increments. If the plus (+) or minus (-) button is held in the display will increase or decrease in 10 minute increments. If the plus (+) or minus (-) button is not depressed within 5 seconds of depressing the Timer button the Timer button will have to be depressed again to again call up the timer mode. • Once the desired time interval is set release the buttons. • The timing interval will start after approximately 4 seconds. • The indicator word TIMER will remain in the display during timer countdown. • The timer will countdown in minutes until the last minute when it will switch over and countdown in seconds. • At the end of the timing interval the indicator word TIMER will blink on and off and three "beeps" will be heard. • The display will return to time of day or any active programmed function and "beeping" will continue every 10 seconds until any button is touched. • Once any button is touched the ...

Download now

Please, enter two numbers from picture: