Votes - 5, Average rating: 4.2
(
)
)
|
manual abstract
NOTICE. Do not use toppings (butter, etc.) on product as product is inverted during normal operation. NOTICE: Operating toaster without legs invalidates any warranty claims. NOTICE: Neglecting to keep fan opening clean could result in toaster failure. 4 4. INSTALLATION INSTRUCTIONS 5. OPERATION INSTRUCTIONS I. Check Contents: 2. Toaster Placement: 1. Preparation 2. Normal Use Refer to Figure 1, account for the following parts: A. Remove foam pad and slide reflector tray inwith wire feeder in upright position as shown. B. Ensure tray is properly engaged in tray slides.To do this simply hold the front of the tray higher than the rear as the back of the tray must slide under the slide on either side,Youwill know if done correctly because traywill be secure.No rocking or teeteringwill take place. C.ToastDrawer - shipped in place D. Instruction Manual - shipped loose A. Locate toaster near a grounded receptacle of the proper configuration (see below). Plug the cordset directly into receptacle (DONOTUSEANEXTENSION CORD). 1. In theU.S.: 208, 230/240V uses NEMA6-20R. B. Place toaster on flat surface providing following minimum clearances: 1. Base = one inch (provided with legs installed). 2. Side and back walls = two inches 3. Overhead = Enough space to allow adequate heat displacement. C. Position toaster where customerswill not contact any surface labeled “CAUTION HOT”. A. Clean toaster thoroughly before first use (See cleaning instructions). B. Controls Familiarity 1. Main Power Switch (located on very bottom of control panel): There are two rocker switches. The bottom switch powers the unit “ON”. It also turns on the bottom element. The top switch is a standby switch that runs the top element. When the standby switch is in the “ON” position the unit is at full power. When the standby switch is in the “OFF” position the unit is running at 50%. a) Full Power: Flip both rocker switches to the right. b) Power Off: Flip both rocker switches to the left. c)Warm-up time:Allow five (5)minutes. A. Loading Product 1. Place product on Wire Feeder. The conveyor will automatically draw product through the toaster at a speed determined by conveyor speed control. 2. Conveyor Speed Control: Set knob to the three (3) position for warm-up. B.Toasting Darkness: determined by conveyor speed &thermostat control. 1. Darkest toasting - set conveyor speed control to far left setting & thermostat controls to highest setting. 2. Lightest toasting - set conveyor speed control to far right setting. 3. Other factors affecting toasting darkness. 3. Thermostat Controls: A. The top thermostat runs the top element &the bottom thermostat runs the bottom element. Figure 1 C B A 5 ! WARNING:Operating toasterwithoutReflectorTray reduces toasting capabilities. ! 6 a) Product moistness - moister product requires slower speeds b) Sugar content in product - product with more sugar requires slower speeds c) ProductTemperature - cooler product requires slower speeds 4. For best results, use day old bread stored room temperature. A. With toaster off and cool, turn toaster on and set conveyor speed to four. B. Using a plastic abrasive pad, wipe the conveyor belt in a back and forth motion (side-to side) motion to remove baked-on product. Wipe the conveyor belt in the same manner with a hot, damp cloth. C.Turn off toaster. D. Slide the reflector/crumb tray out of toaster by pulling forward. Dispose of crumbs and wash tray in hot, soapy water.Dry tray and place back in toaster. E. Remove toast drawer from toaster by sliding out and lifting up. Dispose of crumbs and wash drawer in hot, soapy water. Wipe crumbs from inside the toaster with a hot, damp cloth. Dry drawer and place back in toaster. F. Wipe the exterior surfaces of the toasterwith a hot, damp cloth. 6. CLEANING INSTRUCTIONS 1. Daily Cleaning 7. SPECIFICATIONS XTRM-2 3 INCH 208V 2850W ISOMETRIC VIEW 20.511 2.633 6.654 2.820 5.593 50° 2.521 (64mm) 20.323 (516mm) 50° 2.820 (72mm) 5.593 (142mm) 6.654 (169mm) 16.254 15.067 13.323 16.254 (413mm) 16.067 (408mm) 15.067 (383mm) 13.323 (338mm) 1919..240986 (490mm) XTRM-3 3 INCH 8. WIRING DIAGRAM 7 Rear Fan Control Fan Motor Top Element Bottom Element Terminal Block Top EGO Bottom EGO Top Switch Bottom Switch Existing Wire Rheostat EGO EGO H2 H2 Top Top L1 L1 P1 P1 Pilot Pilot P2 P2 H1 H1 L2 L2 BLACK BLUE L1 L1 L1 L2 L2 G 1 1 1 2 2 4 1 2 3 BLACK BLUE BLUE 7 7 7 6 6 6 6 7 8 8 8 8 12 12 13 13 14 14 14 12 L1 L2 L2 BLACK 2 3 3 3 3 4 4 4 5 5 5 5 5 9 9 9 10 10 10 10 11 11 11 11 15 15 L1 L2 16 16 16 19.293 (490mm) 16.775 (426mm) ISOMETRIC VIEW 2.518 (64mm) 20.655 (525mm) 50° 2.820 (72mm) 6.654 (169mm) 5.593 (142mm) 19.254 (489mm) 15.067 (383mm) 16.067 (408mm) 16.323 (415mm) XTRM-2 3 INCH - EXPLODED VIEW 9. PARTS LISTS & EXPLODED VIEWS 11 63 26 34 22 15 44 36 13 53 29 49 21 40 20 45 18 42 28 54 39 5 4 2 1 7 8 56 58 60 31 32 25 62 23 46 16 27 9 43 30 64 61 4 46 38 28 34 17 20 18 33 50 51 8 12 13 14 36 42 11 10 16 1 41 15 3 25 43 6 24 2 29 31 47 57 55 23 21 35 59 8 9...