1 Open meter, insert 10-test disc, close meter. 2 Pull (a) and push (b) handle to expose test strip. 3 Apply sample. 1 3 2 ba Bayer Diabetes Care Helpline: 1-800-268-7200 IntroductIon IntroductIon1ALookAtYourMeter2expLAnAtIonofdIspLAYsYMboLs4testIngMAterIALs6EvEryday usE InsertIngA10-testdIsc7runnIngAbLoodgLucosetest10marking a deleted blood test 17understanding your test results 18runnIngAcontroLtest20marking a control test 22BEyond EvEryday usE recALLIngtestresuLts24viewing your averages 25cle

All rights reserved. This product is covered by U.S. Patent Nos. 6,551,276 and 6,554,798. Other U.S. and/or foreign patents may be pending. Paradigm®, Quick-serter®, Quick-set®, Silhouette®, and Sof-set®, are registered trademarks of Medtronic MiniMed. CareLink™, Bolus Wizard™, Dual Wave™, Easy Bolus™, Paradigm Link™, ParadigmPAL™, and Square Wave™ are trademarks of Medtronic MiniMed. BD Logic™ is a trademarks of Becton, Dickinson and Company. The Link™ is a trademark of Becton, Dickinson and Co

The decision as to the necessity of a protective conductor test in this case is to be taken by a qualified electrician who should also assume responsibility. You can omit the protective conductor test by pressing the key as soon as the following instruction is shown: „Please connect the probe with the protective conductor of the DUT“. Protective Conductor and Insulation Resistance Measurements for Permanently Installed Devices Under Test ! Attention! Deactivate the electrical system which suppli

This is dependent on country standards. In Canada, the correct unit of measurement is millimoles per liter or “mmol/L.” In other countries the standard may be milligrams per deciliter or “mg/dL.” If a user's meter is set up with the incorrect unit of measure they may have difficulty interpreting their result and this could lead to improper management of their diet or diabetes medication to control blood sugar levels. Currently, with Abbott Diabetes Care meters, the only way to change the “unit

If your ratio value is outside the range, this the usual range of 5-50.* warning message will appear on the screen. ESC to correct, ACT to continue Press ESC to correct or ACT to continue. (* 0.3 - 3.0 for exch) To set just one ratio: To set more than one carb ratio: 6 The screen will return to the EDIT SETTINGS screen. Set your BG Units as described in the “BG (blood glucose) units” on page 69. 68 Chapter: 5 a. Press ESC. using grams using exchanges (flashing) (flashing) SET START TIME 2 _: _ g

200 T. 1 VDE N L L N SL 3 2 1 1 2 3 Feature F01 19 20 18 17 23 18 22 21 16 These operating instructions describe an instrument with firmware version 6xx. . Note Contact problems with exposed conductive parts when using the standard probe with test tip In order to assure good contact, surface coatings must be removed from devices under test with special tools at a suitable location so that the surface has a metallic shine. The tip of the test probe is not suitable for scratching away paint, becau

Designed for ease of use, this system was produced in close association with diabetes healthcare professionals, hospitals and, most importantly, people with diabetes. The Accu-Chek Sensor System is intended for self-testing of glucose in capillary whole blood by persons with diabetes. The lightweight, portable meter provides accurate results in seconds. When you dose the test strip, the meter measures your blood glucose level and displays your result. It’s that simple. Before using your Accu-Che

We understand that people who regularly check their blood glucose levels want a meter that is simple, straightforward and easy to use. As you use your Ascensia® BREEZE™ System, you will appreciate the: • Ease of running a test, and discarding a used test strip. • Use of a 10-Test Disc—which means no individual test strips to fumble with. • User-friendly design—buttons make recalling your results or setting the time as easy as making a telephone call. • Ease of recalling a 14-Day Average. This ea

Using another control solution could present incorrect results. Remove a test strip from the bottle. Tightly close the bottle lid Immediately after you have removed the test strip. NOTE: Check the expiry and discard date. Make sure the test strip does not appear torn or damaged. Hold the test strip with the grey end facing up. Insert the grey end into the test strip port on the meter. The meter will turn on. A test strip with a flashing blood drop will appear letting you know the meter is r

Our goal is to make this the simplest, most straightforward Meter you’ll ever use. Additional Materials: • Ascensia™ MICROFILL™ Test Strips—Use for blood glucose or control solution testing. Come in handy bottle with an easy-to-open flip-top lid. • Ascensia™ MICROLET® Adjustable Lancing Device— Use for finger puncture with an Ascensia™ MICROLET® Lancet. • BATTERIES—Uses two 3-volt (CR2032) lithium batteries. Replace when necessary. For short simple instructions, a quick reference guide is also p