Login:
Votes - 2, Average rating: 3.5 ( )

User manual Bolens, model 244-650-000

Manafacture: Bolens
File size: 1.97 mb
File name: a68613f5-ef64-99e4-3104-8ff27ecfda74.pdf
Language of manual:en
Free link for this manual available at the bottom of the page



manual abstract


Avoid wearing loose fitting clothing. 3. This machine should be operated only upon an earthen level surface. 4. Assure that all screws, nuts and bolts and other fasteners are properly secured. OPERATION 1. When feeding shreddable material into this equipment, be extremely careful that pieces of metal, rocks, bottles, cans or other foreign objects are not included. 2. If the cutting mechanism strikes any foreign object or if your machine should start making an unusual noise or vibration, immediately stop the engine and disconnect the spark plug wire from the spark plug. Allow the machine to stop and take the following steps: A. Inspect for damage. B. Replace or repair any damaged parts. C. Check for any loose parts and tighten to assure continued safe operation. 3. The engine must be kept clean of debris and other accumulations. 4. Do not allow an accumulation of processed material to build up in the discharge area as this will prevent proper discharge and can result in kick-back from feed opening. 5. Never allow your hands or any other part of your body or clothing inside the feeding chamber, discharge chute or near any moving part while the engine is running. 6. Keep all guards and deflectors in place and in good working condition to assure continued safe operation. 7. Always stand clear of the discharge area when operating this machine. 8. Keep your face and body back from the feed opening to avoid accidental bounce back of any material. 9. Do not over-reach. Keep proper balance and footing at all times. 10. The engine governor settings on your machine must not be altered, changed, or tampered with. The governor controls the maximum safe operating speeds and protects the engine and all moving parts from damage caused by overspeed. 11. Do not transport machine while engine is running. MAINTENANCE AND STORAGE 1. When this equipment is stopped for servicing, inspection, storage or to change an accessory, make sure the spark plug wire is disconnected from the spark plug. The machine should be allowed to cool down before making such inspection, adjustments, service, etc. Maintain your machine with care and keep it clean for the best and continued safe operation. 2. When not in use, your machine should be stored out of the reach of children. Keep where gasoline fumes will not reach an open flame or spark. For long periods of storage, the gasoline should be drained and disposed in a safe manner. Always allow the machine to cool before storing in any enclosure. 3 I FIGURE 1 ASSEMBLY INSTRUCTIONS TOOLS REQUIRED FOR ASSEMBLY 1. (1 ) 7/16" Open End or Box Wrench 2. (1)1/2" Open End or Box Wrench 3. (1) Adjustable Wrench 1. Remove the shredder, hardware pack and all parts and literature from the carton before discarding carton. m il B rji c n CTZ3 B r D3 mi c—<© <£> <®> <£> CONTENTS OF HARDWARE PACK A (3) Hex washer head self-tapping screws B (8) Hex screws 1/4-20 x 1/2" long C (8) Hex center lock nuts 1/4-20 thread FIGURE 2 4 2. Place the chute deflector and deflector side plates in position on the left hand side of shredder. 3. Secure with four hex screws (B) and hex center lock nuts (C). Heads of screws are assembled from the inside. Nuts go on the outside. Start all four screws and nuts, then tighten with an adjsutable wrench and 7/16" wrench. See figure 3. FIGURE 4 4. Place the hopper on the shredder. Start all three self-tapping screws (A) by hand, then tighten with a 1/2" wrench. See figure 4. 5. Loosen the hand knob on the right hand side of the shredder. See figure 5. 6. Place upper guide extension in place on guide extension. Secure with four hex screws (B) and hex center lock nuts (C). A 7/16" wrench and adjustable wrench are required. See figure 5. FIGURE 5 5 K DRAWSTRING ■ aimd LOCK 7. Place the bag over the chute deflector. Pull on the drawstring and lock. See figure 6. CHUTE DEFLECTOR FIGURE 6 OPERATION BEFORE STARTING ENGINE 1. Fill fuel tank with fresh regular gasoline. Do Mot mix oil with gasoline. 2. Fill crankcase with oil. Refer to separate encine manual packed with your shredder. TO START ENGINE Tecumseh Engine 1. Place control lever (on engine) in "RUN" pasi-tion. See figure 7. 2. For cold engine start, move carburetor con rol to "CHOKE" position. See figure 7. NOTE A warm engine may not require choking. FIGURE 7 - TECUMSEH ENGINE 3. Pull rewind starter using a quick, full arm stroke. Keep a firm grip on the handle. Return rope slowly. 4. After engine starts, move choke lever on carburetor gradually to "OFF" position. Briggs and Stratton Engine 1. Place control lever (on engine) in "CHOKE" position. See figure 7A. NOTE A warm engine may not require choking. Simply place control lever in "RUN" Position. FIGURE 7A - BRIGGS AND STRATTON ENGINE 2. Pull rewind starter using a quick, full arm stroke. Keep a firm grip on the handle. Return rope slowly. 3. After engine starts, move control lever gradually to "RUN" position. 6 ...

Other models in this manual:
Chippers - 24650L (1.97 mb)

Reviews



Your review
Your name:
Please, enter two numbers from picture:
capcha





Category