Votes - 2, Average rating: 3.5 ( )

Manafacture: Craftsman File size: 1.23 mb File name: Language of manual:

15 U Unclogging ................................................................ 12 Unpacking ................................................................... 5 W Warranty .................................................................... 3 4 ASSEMBLY INSTRUCTIONS IMPORTANT: This unit is shipped WITHOUT GASOLINE or OIL. After assembly, see operation section of this manual for proper fuel and engine oil recommen dations. NOTE: To determine right and left hand sides of your chipper-shredder, stand behind and face the hopper (engine is at the front of the unit). Your chipper-shredder has been completely assembled at the factory, except for the chute deflector and the catcher bag. A pair of safety glasses are also included in the carton. (Inside. Hin( Bolt Chute Deflector Hex Nut Knob FIGURE 1, \ Drawstrin Catcher TOREMOVE FROM CHIPPER-SHREDDERCARTON Cut the corners of the carton. Remove all packing inserts. Roll chipper-shredder out of the carton. Make certain all parts, literature and the safety glasses have been removed before the carton is discarded. TOOLS REQUIRED FOR ASSEMBLY (2) 7/16" or Adjustable Wrenches HOWTOSET-UPYOURCHIPPER-SHREDDER MAKE CERTAIN THE SPARK PLUG& WIRE IS DISCONNECTED AND MOVED AWAY FROM THE SPARK PLUG BEFORE ASSEMBLING THE CHIPPERSHREDDER, ATTACHING THE CHUTE DEFLECTOR • Remove the hand knobs and cupped washers from each side of the discharge opening on the left side of the shredder. • Remove the hex lock nut, two spacers and hex bolt from inside the hinge on top of the discharge opening. Do not remove one spacer from the hex bolt. • Place the chute deflector in position on the discharge opening. Insert bolt through hinge on chute deflector and housing (spacer fits inside hinge). • Place second spacer over the hex bolt, inside the other part of hinge. Secure with hex lock nut. Tighten securely. • Secure both sides of the chute deflector to the housing using hand knobs and cupped washers (cupped side of washers go against chute deflector). ATTACHING THE CATCHER BAG Your chipper-shredder is equipped with a catcher bag to catch the shredded material. • To attach bag, place bag opening over the chute deflector so it completely covers chute opening. Depress plunger on drawstring, pull on drawstring until bag is tight around chute opening. Release _plunger to lock it into position. See figure 2. FIGURE 2. 5 OPERATION KNOW YOUR CHIPPER-SHREDDER READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR CHIPPER-SHREDDER. Compare the illustrations with your chipper-shredder to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. Hopper 31y Chipper Chute Chute Deflector Lever Control Catcher Bag Starter Handle FIGURE 3. MEETS ANSI SAFETYSTANDARDS Sears chipper-shredders conform to the safety standards of the American National Standards Institute. OPERATINGCONTROLS(See figure 3) CHOKE LEVERmUsed to enrich the fuel the carburetor when starting a cold engine. mixture in THRO'I-FLE stops the enCONTROL--Controls engine speed and gine. STARTER engine. HANDLEmUsed to manually start the BEFORE USING YOUR CHIPPER-SHREDDER, AGAIN REFER TO THE "SAFETY RULES" AS SHOWN ON PAGE 2 OF THIS MANUAL. ALWAYS BE CAREFUL. The operation of any chipper-shredder can result in foreign objects being thrown into the eyes, which can result in severe eye damage. Always wear the safety glasses provided with the chipper-shredder or eye shields before chipping or shredding, or while performing any adjustments or repairs. We recommend Wide Vision Safety Mask for over spectacles or standard glasses available at Sears Retail or Catalog Stores. TO STOP ENGINE No Larger • Move throttle control lever to OFF position. See fig1/ 2" Diameter ure 4. (Recommended) Or 1" Diameter • Disconnect spark plug wire and move away from (Maximum) spark plug to prevent accidental starting while equipment is unattended. Tt Control FIGURE 4. HOW TO USEYOUR CHIPPER-SHREDDER Do not attempt to shred or chip any material other than vegetation found in a normal yard (i.e., branches, leaves, twigs, etc.). WARNING: THE CHIPPER-SHREDDER ,_ DISCHARGESVELOCITY. WITH CONSID-FROM ERABLE MATERIALS KEEP AWAY THE AREA AROUND THE CHUTE DEFLECTOR. ALWAYS STOP THE ENGINE AND DISCONNECT THE SPARK PLUG WIRE WHEN REMOVING OR ATTACHING THE BAG, WHEN CHANGING CONTAINERS OR WHEN REMOVING THE SHREDDED MATERIAL. WEAR SAFETY GLASSES AND GLOVES WHENEVER USING YOUR CHIPPER-SHREDDER. The chipper-shredder is designed for two different methods of operation. • Leaves and small branches up to 1/2" diameter (recommended) or 1" diameter (maximum) can be fed into the hopper assembly. See figure 5. If it becomes necessary to push material into the chipper- shredder, use a small diameter stick--NOT YOUR HANDS. The stick should be small enough that it will be ground up if gets into the impeller assembly. WARNING: DO NOT PUT MATERIAL LARGER THAN 1/2" IN DIAMETER (RECOMMENDED) or 1" DIAMETER (MAXIMUM) INTO THE HOPPER ASS...

Download now

Please, enter two numbers from picture: