Votes - 3, Average rating: 4 ( )

Manafacture: Sears File size: 830.9 kb File name: Language of manual:

Release plunger to lock it chute opening. Depress the plunger on the draw- into position. See figure 5. * _OPERATION_ KNOW YOUR CHIPPER-SHREDDER READ THIS OWNER’S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR CHIPPER-SHREDDER. Compare the illustrations with your chipper-shredder to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. Hopper Assembly 1 Chipper Starter Chute Handle FIGURE 6. MEETS ANSI SAFETY STANDARDS Sears chipper-shredders conform to the safety standards of the American National Standards Institute. OPERATING CONTROLS (See figure 6) RELEASE BAR—Used to release the hopper when raising or lowering. CHOKE LEVER—Used to enrich the 1uel mixture in the carburetor when starting a cold engine. BEFORE USING YOUR CHIPPER-SHREDDER, AGAIN PAGE 2 OF THIS MANUAL ALWAYS BE CAREFUL. STARTER HANDLE—Used to manually start the engine. THROTTLE CONTROL—Controls engine speed and stops the engine. REFER TO THE ‘'SAFETY RULES” AS SHOWN ON The operation of any chipper-shredder can result in foreign objects being thrown into the eyes, which can result in severe eye damage. Always wear the safety glasses provided with the chipper-shredder or eye shields before chipping or shredding, or while performing any adjustments or repairs. We recommend Wide Vision Safety Mask for over spectacles or standard glasses available at Sears Retail or Catalog Stores. 7 BEFORE STARTING GAS AND OIL FILL-UP NOTE: ENGINE IS SHIPPED WITHOUT OIL FILL CRANKCASE WITH OIL BEFORE STARTING. BE VERY CAREFUL NOT TO ALLOW DIRT TO ENTER THE ENGINE WHEN CHECKING OR ADDING OIL OR FUEL. Recommended SAE Viscosity Grades ,4 30 or 10W30 > 1 5V V30 -20° 0° 32° 60° 80° 100° TEMPERATURE RANGE EXPECTED BEFORE NEXT OIL CHANGE. ALL OILS MUST BE A.P.I. SERVICE CLASSIFICATION SD, SE OR SF. • Fill engine with oil as follows. Remove oil fill dipstick. See figure 7. With chipper-shredder level, use a funnel to fill engine with oil to FULL mark on dipstick. Capacity is approximately 11/2 pints. Be careful not to overfill. Tilt chipper-shredder toward the left (from behind the hopper), then re-level. Check oil level. Refill to FULL mark on dipstick if necessary. Replace dipstick and tighten. • Remove fuel cap and fill fuel tank. See figure 8. Use fresh, clean, unleaded automotive gasoline. Capacity is one gallon. Replace fuel cap. WARNING: DO NOT FILL CLOSER A THAN 1/2 INCH OF TOP OF FUEL TANK TO PREVENT SPILLS AND TO ALLOW FOR FUEL EXPANSION. IF GASOLINE IS ACCIDENTLY SPILLED, MOVE CHIPPER-SHREDDER AWAY FROM AREA OF SPILL. AVOID CREATING ANY SOURCE OF IGNITION UNTIL GASO-LINE VAPORS HAVE DISAPPEARED. Check the fuel level periodically to avoid running out of gasoline while operating the chipper-shredder. If the unit runs out of gas as it is shredding or chipping, it may be necessary to unclog the unit before it can be restarted. Refer to “Removing the Flail Screen” on page 13. Caution: Experience indicates that alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be empty before storage for 30 days or longer. Refer to “Storage” section of this manual for details. Use fresh fuel each season. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may result. NOTE: USE CLEAN OIL AND FUEL. STORE IN APPROVED, CLEAN, COVERED CONTAINERS. USE CLEAN FILL FUNNELS. TO START ENGINE WARNING: BE SURE NO ONE OTHER A THAN THE OPERATOR IS STANDING NEAR THE CHIPPER-SHREDDER WHILE STARTING OR OPERATING. DO NOT OPERATE THIS CHIPPER-SHREDDER UNLESS THE CHUTE DEFLECTOR HAS BEEN PROPERLY INSTALLED AND IS SECURED WITH THE HAND _KNOBS._ • Attach spark plug wire and rubber boot to spark plug if necessary. See figure 8. • Place the throttle control lever in FAST position. See figures 8 and 9. • Move choke lever to CHOKE position. • Grasp starter handle (see figure 8) and pull rope out slowly until engine reaches start of compression cycle (rope will pull slightly harder at this point). Let the rope rewind slowly. NOTE: A noise will be heard when finding the start of the compression cycle. This noise is caused by the flails and fingers which are part of the shredding mechanism falling into place, and should be expected. • Pull rope with a rapid, continuous, lull arm stroke. Keep a firm grip on start handle. Let rope rewind slowly. Do not let starter handle snap back against starter. • Repeat preceding two instructions until engine fires. When engine starts, move choke lever on engine halfway between CHOKE and RUN. NOTE: If engine does not fire after three attempts, move choke lever halfway between CHOKE and RUN position and try again. • Move throttle control to SLOW position for a few minutes warm-up. Move choke lever ...

Download now

Please, enter two numbers from picture: